Emerson 5100 installation manual Detail Screen for Series 300 ATSs

Page 19

Connectivity Module

Series 300 ATSs 3-3

Detail Screen for Series 300 ATSs

The Detail Screen for Series 300 ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, and other status indications.

ATS one-line icon shows position & source status (green or red circle means source is acceptable, grey circle means source is not acceptable)

Status of

 

 

ATS location

Emergency Source

ATS name

ATS type

Status of Normal Source

 

 

Actual voltage

 

 

 

& frequency

 

 

Actual voltage

readings from

 

 

 

 

reading from

ATS controller.

 

 

 

 

ATS controller.

 

 

 

Voltage &

 

 

Voltage &

frequency

 

 

frequency

settings in ATS

 

 

settings in ATS

controller.

 

 

controller.

Engine start signal

Active

 

Active time delays

time delays

 

 

(red means active)

Load connected to Normal or Emergency Source

 

Detail Screen for Series 300 ATSs with a Power Manager

The Detail Screen for Series 300 ATSs with a Power Manager is the same as above and adds information from the PM (voltage, current, power, and rating).

Detail Screen for Series 300 ATSs with a Digital Power Meter

The Detail Screen for Series 300 ATSs with a Digital Power Meter is the same as above and adds information from the DPM (voltage, current, power, and rating).

Image 19
Contents 381333-367 C Connectivity ModuleImportant information Who Should Use this Installation ManualIi Welcome Connectivity Module PrerequisitesDIP Switch on bottom of unit SpecificationsInstallation Overview Check the DIP Switch Settings for RS485Iv Outline and Mounting Drawing Connectivity Module Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams Vii Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams Status LEDs LED Description LED Function / Mode of OperationConnectivity Module Status LEDs How to Install the Connectivity Module on Asco 940/962 ATSs InstallationHow to Test Communication to the Connectivity Module Connectivity Module InstallationInstallation Connectivity Module Http//169.254.1.1/config.htmDevice Configurator Screen for 7000 & 4000 Series ATSs Device Configurator Screen for 7000 & 4000 Series ATSsGroup 5 Controller Configuration right side Connectivity Module server Configuration left sideInput Name & Output Names Power Manager only Power Manager or Power Meter Configuration7000 & 4000 Series ATSs Connectivity Module Accessory 85 Descriptive Tags Assigned Detail Screen for 7000 & 4000 Series ATSs Connectivity Module Series 300 ATSs Device Configurator Screen for Series 300 ATSsGroup 1 Controller Configuration right side Device Configurator Screen for Series 300 ATSsSeries 300 ATSs Connectity Module Power MeterDetail Screen for Series 300 ATSs Detail Screen for Series 300 ATSs with a Power ManagerPage Device Configurator Screen with Power Manager Device Configurator Screen for Asco 940/962 ATSsGroup 7A Controller Configuration right side Device Configurator Screen without Power ManagerDetail Screen for Asco 940/962 ATSs Detail Screen for Asco 940/962 ATSs with a Power ManagerAsco 940/962 ATSs Connectivity Module Input names Display Input & Output Names screen Output names Detail Screen for Digital Power Meters connected to a Load Detail Screen for Power Managers connected to a LoadDetail Screen for Power Detail Screen for Power Managers connected to a GeneratorDetail On Local Area Connection Properties screen Select All Programs Accessories Command Prompt Problem Cause Connectivity Module Troubleshooting A-3Read Requests Third Party Modbus Device ConfigurationSnmp Trap messages Connectivity Module Snmp Internet-standard Protocol A-5Snmp Internet-standard Protocol Connectivity Module Problem Cause SolutionSerial No Row IP Address Subnet Mask GatewayCatalog No Address set ATS Controller PM or DPM Communication Address Form for Connectivity Module CM Communication Address Form for Connectivity Module CM Index