Emerson 5081-T instruction manual Lsl Usl, C/T-HT HART/Model 375 Menu Tree 2

Page 68

MODEL 5081-T

SECTION 9.0

 

OPERATION WITH MODEL 375

Basic setup (continued)

Device information

Distributor

Model

Dev id

Tag

Date

Physicl signl code

Write protect

Snsr text

Descriptor

Message

Revision #'s

Universal rev Fld dev rev Software rev

Hardware rev

Detailed setup Sensors

Main sensor

PV Type [Conductivity, Resistivity, 0-12% NaOH, 0-15% HCl, 0-25% H2SO4, 96-99.7% H2SO4, Custom]

PV Snsr unit [uS/cm, mS/cm, mS/m, Mohm-cm, %, ppm, _] Cond unit [uS/cm, mS/cm, mS/m] ****

Define curve ****

View custom points ****

Cell constant

Temp comp type [Linear, Neutral salt, Cation, None/Off] *.. Temp slope

Ref temp ***, ****, *. PV sensor type Sensor information

LSL

USL

Min span

Temperature

ATC [On, Off]

Man temp

Temp unit [ºC, ºF]

Temp snsr [RTD PT100, RTD PT1000]

Diag override (continued)

Offset error [ON, OFF]

Zero warning [ON, OFF]

Overrange [ON, OFF]

Sensor fail [ON, OFF]

FIGURE 9-2. 5081-C/T-HT HART/Model 375 Menu Tree (2 of 4)

62

Image 68
Contents Model 5081-T Essential Instructions Rev. Level DateModel 5081-T Table of Contents CONT’D Iii List of FiguresNumber Title List of Figures CONT’D List of TablesSection Description and Specifications Simple Menu StructureHart Recommended Ranges for Toroidal Sensors Recommended SensorsAtex I T N E X T Transmitter Display During Calibration and ProgrammingOverview of Hart Communication Hart Interface DevicesFoundation Fieldbus AMS Main Menu Tools Section Installation Mechanical InstallationUnpacking and Inspection Orienting the Display BoardMounting on a Flat Surface 40308103 Pipe MountingInductive Loops Sensor SelectionModel 5081-T Sensor Selection Recommended SensorsPower SUPPLY/CURRENT Loop Power Supply and Load Requirements. Refer to FigurePower Supply-Current Loop Wiring Model 5081-T-HTPower Supply Wiring for Model 5081-T-FF/FI Typical Fieldbus Network Electrical Wiring ConfigurationSection Wiring Sensor Wiring Electrical InstallationSensor Wiring Wiring Through a Junction BOXPower Wiring Model 5081-T-HT Power Wiring Model 5081-T-FFElectrical Installation Wiring Model 242 sensor to Model 5081-T transmitterSection Section IRC Infrared Remote Control Section Intrinsically Safe & Explosion ProofFM Explosion-Proof Installation for Model 5081-T-HT FM Intrinsically Safe Installation for Model 5081-T-HT CSA Intrinsically Safe Installation for Model 5081-T-HT Atex Intrisically Safe Label for Model 5081-T-HT Atex Intrisically Safe Label for Model 5081-T-HT FM Explosion-Proof Installation for Model 5081-T-FF FM Intrinsically Safe Installation for Model 5081-T-FF 10. CSA Intrinsically Safe Installation for Model 5081-T-FF 11. Atex Intrisically Safe Label for Model 5081-T-FF 12. Atex Intrinsically Safe Installation for Model 5081-T-FF FI-T 9241515-01 15. FM Intrinsically Safe Installation for Model 5081-T-FI 9241516-01 17. CSA Intrinsically Safe Installation for Model 5081-T-FI 18. Atex Intrisically Safe Label for Model 5081-T-FI 19. Atex Intrinsically Safe Installation for Model 5081-T-FI Section Display and Operation DisplaysS U I T N E X TInfrared Remote Controller IRC KEY Functions Infrared Remote ControllerTo reset transmiter to factory default settings Quick Start for Model 5081-T-HT HartQuick Start for Model 5081-T-FF/FI Foundation Fieldbus Menu Tree Conductivity 25.0C 12.00mAProcess Display Calibration ProgramProgram Menu Mnemonics Diagnostic Messages Default SettingsDefault Settings for Model 5081-T-HT Using Hold SecurityEntering the Security Code Retrieving a Lost Security CodeAccessing the Calibrate Menu Section START-UP and CalibrationCalibrate Menu Model 5081-T-FFProcedure 9URUTemp Slope Output Cal5ES-U1 U17!91GM!91 U91Model 5081-T-HT Model 5081-T-FF Section ProgramingGeneral Definitions Output 5081-HT onlyPurpose Procedure 9VUVU4QG UhtuU7-P Process temperature is. Press Enter to saveTemp Display G5-AHCL H2SO4LHart GgshttSetup Cust PVO!RUT!!%SHI 8VO!UTDefault Setting Measurement Range Over Range Warning LimitRange G12-USection Foundation Fieldbus Operation PIDConnecting the Communicator Section Operation with ModelOff-line and On-line Operation Making Hart related settings from the keypadOperation PV LRV PV URV C/T-HT HART/Model 375 Menu Tree 1LSL USL C/T-HT HART/Model 375 Menu Tree 2LRV URV AO1PV AO PV LRV PV URV C/T-HT HART/Model 375 Menu Tree 4Resource Faultstate Blockerr Featuresel Rsstate FaultstateLimnotify MaxnotifyAlarmhys StrevBlockerr TagdescAlertkey Hihilim PvftimeLowcut Strev Statusopts StrategyLolim LolopriLololim IooptsReset Rate ResetSphilim Splolim Bkcalhys FfgainBaltime BypassControlopts SphilimStrev Rate Tagdesc Alertkey OuthilimDvhipri DvlopriC/T-FF/FI Model 375 Menu Tree 9 C/T-FF/FI Model 375 Menu Tree 10 Current Operating Menu Section Diagnosis and TroubleshootingOverview DLS Tqiu4DSG IdvnutNON- Disabling Warnings Fault ConditionsDisabling Faults 9IITHU!1SS 9WHS!S-PJ1Hssqs Quick Troubleshooting Guide Quick Troubleshooting GuideSymptom Action Field TroubleshootingSystematic Troubleshooting Troubleshooting Flow ChartRTD Resistance Values FormulaExample RTD Resistance ValuesWhen a Warning condition exists When a Fault existsTroubleshooting When a Fault or Warning Message is Showing Temp HITemp LO CPU FailRtd FAIL, Temp HI, and Temp LO CPU Fail and ROM Fail Section Maintenance Preventative MaintenanceTransmitter Maintenance 0 C 2 1 0 % mAReplacement Parts for Model 5081-T Transmitter Exploded View of Model 5081-T TransmitterSection Theory of Operation ConductivityHart Communication Output LogicWarranty Repair NON-WARRANTY RepairSection Return of Material GeneralThis page intentionally left blank Warranty Return of MaterialSpecifications subject to change without notice