Fujitsu BX600 SB9 manual

Page 17

White Paper ⏐ Issue: October 2006 ⏐ Integration of BX600 SB9 Switches in Cisco Networks

name VLAN-10

!

vlan 20 name VLAN-20

!Define the port-channels

interface Port-channel1

switchport trunk encapsulation dot1q switchport mode trunk

interface Port-channel3

switchport trunk encapsulation dot1q switchport mode trunk

interface GigabitEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk channel-group 1 mode on

interface GigabitEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk channel-group 1 mode on

interface GigabitEthernet0/23 switchport trunk encapsulation dot1q switchport mode trunk channel-group 3 mode on

!

interface GigabitEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk channel-group 3 mode on

!Cisco Switch B

!Enable and configure RSTP

spanning-tree mode rapid-pvst spanning-tree vlan 1,10,20 priority 4096

!Timers are tuned. Please refer Cisco documentation before

!using this part of the configuration

!

spanning-tree vlan 1,10,20 hello-time 1 spanning-tree vlan 1,10,20 forward-time 8 spanning-tree vlan 1,10,20 max-age 11

!

vlan 10 name VLAN-10

!

vlan 20 name VLAN-20

!Define the port-channels

interface Port-channel2

switchport trunk encapsulation dot1q switchport mode trunk

interface Port-channel3

switchport trunk encapsulation dot1q switchport mode trunk

interface GigabitEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk channel-group 2 mode on

interface GigabitEthernet0/2 switchport trunk encapsulation dot1q

Page 17 / 47

Image 17

Contents Switch Management Contents Introduction Switch ConnectivityBasic Multicast Services Page Introduction Auto Negotiation Recommended SolutionConfiguration Port Aggregation Network problemsShut down the affected ports to avoid loops Set up the port-channelVerify the operation of the port-channels Bring up the affected portsVLANs and Trunks Vlan Trunk between SB9 and Cisco SwitchDefine the VLANs Configure the port-channelsConfigure Vlan trunk Gvrp Verify the Vlan trunkRunning ST P 802.1D with PVST+ on Vlan Trunks Spanning Tree ProtocolRunning PVST+ on Vlan Trunks while disabling STP at the SB9 SB9Rapid Spanning Tree Combining RAPID-PVST and 802.1wCombining RAPID-PVST and 802.1w after failure of Po1 Configuration with Vlan Trunks SB9 SwitchConfigure the switches Network loopsPage Page STP Verify the configurationPage Configuration without Vlan Trunks Configuration example Rstp without Vlan trunksPage Mode Type State Role Enabled Forwarding Designated Disabled Enabled Disabled PC Mbr Manual forwarding Interface BX600 port mapping Access Port and NIC ConfigurationConfigure the access ports of the switches Typical access port configurationConfigure the Broadcom NIC Page Configure the Intel Adapter Page Select Switch Fault Tolerance and press Next Press Finish Link State Configure a Link State GroupConfiguration Recommended solutionEnable multicast routing and Igmp at the layer 3 switch Enable Igmp snooping at all Layer 2 switchesVlan Page Configure the SB9 for unicast Sntp Configuration of syslog and SntpConfigure the SB9 for broadcast Sntp Configure the SB9 for logging and syslogTest the configuration Configure Snmp for SNMPv1 and SNMPv2c Configuration of SnmpConfigure SNMPv3 authentication SnmpConfiguration of SSH Remote Console AccessConfigure the SB9 Test the loginPrepare the ACS Configuration of RadiusIntegration into Radius and TACACS+ Page Specify the user’s password and press Submit Test the login Configuration of Tacacs Page Configure the SB9 Cisco Discovery Protocol Configuration of CDPCheck the configuration Further information in the Internet Configuration of Port MonitoringPort Monitoring