Xerox KS-801 10/100BASE-TX Fast Ethernet Switched Ports, MDI-X and MDI RJ-45 Connectors

Page 13

•10/100BASE-TX Fast Ethernet Switched Ports

Each switched port supports one connection to a LAN segments. Each segment is an independent shared network in one collision-domain. The connection can be to either a 10BASE-T or a 100BASE-TX device.

•MDI-X and MDI RJ-45 Connectors

MDI-X jack is labeled [X] normally to indicate the jack is designed with internal crossover function. It allows a connection to an end station using straight-through UTP cable. MDI RJ-45 connector is provided for easy uplink via standard straight-through UTP to other device that supports MDI-X RJ-45 connector. The following table shows the pin assignments of MDI-X and MDI RJ-45 connector respectively:

PIN#	MDI-X Jacks MDI Jack
1	Rx+	Tx+
2	Rx-	Tx-
3	Tx+	Rx+
6	Tx-	Rx-
4,5,7,8	NC	NC

•Crossover SW

This push button switch is dedicated for Port #9 RJ-45 jack. When pushing ON, Port #9 RJ-45 is set to MDI type.

Crossover SW	Port #9 RJ-45
OFF	MDI-X
ON	MDI

•100 Fiber Slot

Optional fiber connectivity support for Port #9. This can not be used with RJ-45 9X jack at the same time. Refer to section 3.3.

-13-

Image 13

Contents 10/100 Fast Ethernet Managed Switch with Fiber Connectivity Trademarks Table of Contents Web Management Console & Telnet ManagementIntroduction Features Page Specifications Packing List Installing the SwitchPanels Install Rack Mount Brackets Mounting the SwitchesInstall the Switch into a 19-inch Rack Desktop MountingMaking Network Connections Network Switched PortsMDI-X and MDI RJ-45 Connectors 10/100BASE-TX Fast Ethernet Switched Ports10/100BASE-TX Fast Ethernet Ports Manual ConfigurationAuto-negotiation Capable Auto-speed-sensingUTP Cable Connections Flow ControlStraight-through and Crossover UTP Cable Fast Ethernet Fiber Slot Module Connector type Fiber cable Maximum lengthModule Outline Fiber Module Top view Fiber Jumper SettingSpecifications Duplex Mode SettingModule Installation Making Trunk Connections Switch supports the following trunk configurationsPage Making Sniffer When doing sniffer, configureMonitored Ports Sniffer PortLED Panels LED IndicatorsInterpretation Management Support Performing Network ManagementManagement objects Login Port StatusConsole Management Setting IP AddressConsole port does not support modem connection Telnet ManagementRefer to for more information Support Snmp ManagementConsole & Telnet Management IP Status Set IP AddressSelect 1 from main menu to set IP address Select 2 from main menu to view IP statusPort status definitions are View Port StatusView Port Counters View STP Status Page Restore Default Values Console Sftp Utility Update Firmware\WINDOWSSFTP Prompts shown on DOS screen are as followsProcessing messages shown on console screen are Remote Boot SystemWeb Management Set IP Address for the SwitchStart Browser Software and Making Connection Web BrowserLogin Login to the SwitchFactory default Username Admin Factory default Password Page Port Status Port Statistics Administrator Basic Click Basic to view or modify the following settingsIP Address IP Address settings areSnmp Entries Use scroll bar to view all settings as followsSnmp settings are Click Advanced in menu to perform AdvancedAdvanced / Spanning Page Page MAC address of the switch as a unique identi Priority is assigned to the switch. The higherValue is lower priority. Range 0 Fier to the networkListening Switches send messages to one another Ports which are enabled can be in one of the followBlocking The switch enters the Blocking State if a Learning The switch enters the Learning State if noAdvanced / Trunking Advanced / Sniffer Page Console Port Information Port Controls Security Manager Click System Manager to perform System ManagerClick Apply to start Tftp file transfer operations Tftp Update FirmwarePage Remote Boot System