Xerox KS-801 operation manual View Port Status, Port status definitions are

Page 30

6.3 View Port Status

Select [3] from main menu to view all LAN port status. The port status are shown like following table style:

---------------------------------------------

Port	LinkStatus PortControl Speed Duplex FlowControl
[1]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[2]	[Link	]	[Enable ]		[10 ]	[Half]	[Enable]
[3]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[4]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[5]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[6]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[7]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[8]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
[9]	[Unlink]		[Disable]		[100]	[Full]	[Enable]
---------------------------------------------
The port status definitions are:
Port Status		States		Interpretation
LinkStatus		Unlink		No active link
		Link		Active link established
PortControl		Disable		Port function is disabled.
		Enable		Port function is enabled.
Speed		100		100Mbps.
		10		10Mbps.
Duplex		Full		Full duplex mode.
		Half		Half duplex mode.
FlowControl		Enable		Flow control function is enabled.
		Disable		Flow control function is disabled.

-30-

Image 30

Contents 10/100 Fast Ethernet Managed Switch with Fiber Connectivity Trademarks Table of Contents Console & Telnet Management Web ManagementIntroduction Features Page Specifications Installing the Switch Packing ListPanels Install the Switch into a 19-inch Rack Mounting the SwitchesInstall Rack Mount Brackets Desktop MountingNetwork Switched Ports Making Network Connections10/100BASE-TX Fast Ethernet Switched Ports MDI-X and MDI RJ-45 ConnectorsAuto-negotiation Capable Manual Configuration10/100BASE-TX Fast Ethernet Ports Auto-speed-sensingFlow Control UTP Cable ConnectionsStraight-through and Crossover UTP Cable Module Connector type Fiber cable Maximum length Fast Ethernet Fiber SlotFiber Module Top view Fiber Jumper Setting Module OutlineDuplex Mode Setting SpecificationsModule Installation Switch supports the following trunk configurations Making Trunk ConnectionsPage Monitored Ports When doing sniffer, configureMaking Sniffer Sniffer PortLED Indicators LED PanelsInterpretation Performing Network Management Management SupportLogin Port Status Management objectsSetting IP Address Console ManagementTelnet Management Console port does not support modem connectionRefer to for more information Snmp Management SupportConsole & Telnet Management Select 1 from main menu to set IP address Set IP AddressIP Status Select 2 from main menu to view IP statusView Port Status Port status definitions areView Port Counters View STP Status Page Restore Default Values Update Firmware Console Sftp UtilityPrompts shown on DOS screen are as follows \WINDOWSSFTPRemote Boot System Processing messages shown on console screen areStart Browser Software and Making Connection Set IP Address for the SwitchWeb Management Web BrowserLogin to the Switch LoginFactory default Username Admin Factory default Password Page Port Status Port Statistics Administrator Click Basic to view or modify the following settings BasicIP Address settings are IP AddressUse scroll bar to view all settings as follows Snmp EntriesSnmp settings are Advanced Click Advanced in menu to performAdvanced / Spanning Page Page Value is lower priority. Range 0 Priority is assigned to the switch. The higherMAC address of the switch as a unique identi Fier to the networkBlocking The switch enters the Blocking State if a Ports which are enabled can be in one of the followListening Switches send messages to one another Learning The switch enters the Learning State if noAdvanced / Trunking Advanced / Sniffer Page Console Port Information Port Controls Security Manager System Manager Click System Manager to performTftp Update Firmware Click Apply to start Tftp file transfer operationsPage Remote Boot System