Canon qy8-13az-000 service manual

Page 10

The remaining ink amount [1683] unknown.

Ink tank not recognized. [1684]

Ink tank not recognized. [1410 to 1419]

Scanning unit (printer

[1200]

cover) open.

 

(Applicable ink tank icon)

The remaining level of the following ink cannot be correctly detected. Replace the ink

tank. (U130)

The following ink tank cannot be recognized. (U140)

(Applicable ink tank icon)

The following ink tank cannot be recognized. (U150)

(Applicable ink tank icon)

Cover is open. Close cover.

-Fill in all the circles on the print head alignment sheet.

-Place the sheet in the correct orientation and position.

An ink tank which has once been empty is installed. Replace the applicable ink tank with a new one.

Printing with a once-empty ink tank can damage the printer.

To continue printing without replacing the ink tank(s), press the OK button for 5 sec. or longer to disable the function to detect the remaining ink amount. After the operation, it is recorded in the printer EEPROM that the function to detect the remaining ink amount was disabled.

A non-supported ink tank is installed (the ink tank LED is turned off). Install the supported ink tanks.

A hardware error occurred in an ink tank (the ink tank LED is turned off). Replace the ink tank(s).

Close the scanning unit (printer cover).

2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or Both LEDs Lit)

Service call errors are indicated by the number of cycles the Alarm LED and Power LED blink, and the corresponding error code is displayed on the LCD.

Cycles of blinking

 

 

 

Solution

in orange (Alarm

Error

Error

Conditions

(Replacement of listed parts, which

LED) and green

code

(Power LED)

 

 

 

are likely to be faulty)

 

 

 

 

2 times

Carriage error

[5100] An error occurred in the carriage encoder signal.

- Carriage unit (QM2-3753)

 

 

 

 

- Timing slit film (QC1-9542)

 

 

 

 

- Logic board (QM2-3827)

 

 

 

 

- Carriage motor (QM2-3872)

3 times

Line feed error

[6000]

An error occurred in the LF encoder signal.

- Timing sensor unit (QM2-3878)

 

 

 

 

- Timing slit disk film (QC1-9597)

 

 

 

 

- Feed roller (QL2-1407)

 

 

 

 

- Logic board (QM2-3827)

 

 

 

 

- Paper feed motor (QM2-3873)

4 times

Purge cam

[5C00]

An error occurred in the purge unit.

- Purge unit (QM2-3754)

 

sensor error

 

 

- Logic board (QM2-3827)

5 times

ASF (cam)

[5700]

This error takes place when feeding paper from the

- Sheet feed unit (QM2-3762)

 

sensor error

 

ASF after an error occurred in the ASF cam sensor.

- ASF_PE sensor board (QM2-3877)

 

 

 

 

- Logic board (QM2-3827)

6 times

Internal

[5400]

The internal temperature is not proper.

- Logic board (QM2-3827)

 

temperature

 

 

- Carriage unit (QM2-3753)

 

error

 

 

 

 

 

 

7 times

Ink absorber

[5B00,

The ink absorber is full.

- Ink absorber kit (QY5-0178)

 

full

5B10,

 

 

 

 

5B01,

Error codes:

 

 

 

5B11]

 

Overseas:

5B00: Main ink absorber

5B10: Borderless-print ink absorber Japan:

5B01: Main ink absorber

1-5

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Pixma MP510 Revision ScopeTrademarks Manual Outline II. Table of Contents Part 2 Technical Reference Periodic maintenance MaintenanceAdjustment Periodic replacement partsPrint head Customer MaintenanceProduct Life Ink tank target valueSpecial Tools Part 1 1. MaintenanceSerial Number Location List of Error Display / Indication Operator Call Errors by Alarm LED Lit in OrangePage Other Error Messages VbusLow ink Restrictions on paper USB cable not connected Troubleshooting by Symptom When enlarged in the carriage movement direction When enlarged in the paper feed directionPart 1 2. List of Error Display / Indication At replacement After replacementRepair Part 1 3. Repair 3-1. Notes on Service Part Replacement Special Notes on Repair Servicing Side cover L2 and front cover L removalSide cover R2 and front cover R removal Main case removal Scanner flexible cable attachment Timing sensor unit cable wiring Carriage unit flexible cable wiring Power supply unit cable wiringInk tube installation Emblem removal Platen link assemblyPart 1 3. Repair 3-2. Special Notes on Repair Servicing Paper feed motor adjustment Adjustment / SettingsCarriage rail adjustment Document pressure sheet adjustment Front feeder paper feed roller cleaningAmount Part 1 3. REPAIR, 3-3 1 to Ink absorber replacement Ink absorber counter setting User modeService mode See Destination settings procedures below Ink absorber counter value to be set % Part 1 3. Repair 3-3. Adjustment / Settings 6 to Service test print Verification ItemsService test print sample Eeprom information print Print samplePrinted items Part 1 3. Repair Verification ItemsMachine Transportation Part NEW Technologies Cleaning Mode and Amount of INK Purged Part 2 2. Cleaning Mode and Amount of INK Purged Print Mode Normal Color Printing via ComputerBorderless Printing via Computer Normal Grayscale Printing via ComputerManual Duplex Printing via Computer Card / Camera Direct Printing Part 2 3. Print ModeCopying FAQ Problems Specific to the MP510 and Corrective Actions To the table of contents To the top Part 2 4. FAQ Appendix Block Diagram Pixma MP510Signal name Function Input Output Connector Location and PIN LayoutJ301 Print Head 1/3 Carriage Unit Signal name Function Logic Board AssyJ501 LF Encoder Signal name Function J505 Asfpe Sensors Signal name Function Input Output J502 Ink Sensor / Ink Tank Sensor Signal name FunctionJ503 Power Supply Unit Input / Output J507 Main Cam Sensor Signal name Function Input /OutputJ702 LF Motor Signal name Function J701 Carriage Motor Signal name FunctionJ703 Purge Unit Motor Signal name Function J801 Scanner Unit Signal name Function J704 Scanner Motor Signal name FunctionJ901 Memory Card Signal name Function Input Output J902 USB 2.0 I/F Signal name Function Input Output J1 Logic Board Signal name Function Input / Output Card Slot BoardSmgnd J3 CompactFlash Signal name Function J5 IrDA Board Signal name Function Input / Output J301 Memory Card Board Signal name Function Input / OutputJ2 LCD Unit Signal name Function Input / Output Operation Panel BoardSignal name Function Carriage BoardPixma MP510 Specifications Scanner CopyDirect printing DpofPage Print head Supported ink tanks
Top Page Image Contents