Canon qy8-13az-000 service manual Ink absorber counter value to be set %

Page 34

<Ink absorber counter setting procedures>

Set the ink absorber counter data to a replaced new EEPROM after the logic board is replaced in servicing.

1)Before replacement of the logic board ass'y, check the ink absorber counter value in EEPROM information print. See 3-4. Verification Items, (2) EEPROM information print.

2)In the ink absorber counter setting mode, press the Stop/Reset button the specified number of time(s) according to the ink absorber whose counter value should be transferred to the replaced new EEPROM.

Time(s)	Ink absorber	Remarks
0 times	Main ink absorber
1 time	Borderless-print ink absorber
2 times	Both the main and borderless-print ink absorbers
3 times or more	Not valid	Press the ON/OFF button to return to the ink absorber counter setting m

3)Press the ON/OFF button to proceed to the next step.

4)The ink absorber counter value can be set in 10% increments by pressing the Stop/Reset button. Press the Stop/Reset button the appropriate number of time(s) to select the value which is closest to the actual counter value (which was checked in step 1) above.

Time(s)	Ink absorber counter value to be set (%)
0 times	0%
1 time	10%
2 times	20%
3 times	30%
4 times	40%
5 times	50%
6 times	60%
7 times	70%
8 times	80%
9 times	90%
	Not valid.

10 times or more

Press the ON/OFF button to return to the ink absorber counter setting mode.

5)Press the ON/OFF button to set the selected value to the EEPROM. Print EEPROM information to confirm that the value is properly set to the EEPROM.

1-29

Image 34

Contents Pixma MP510 Revision ScopeTrademarks Manual Outline II. Table of Contents Part 2 Technical Reference Periodic maintenance MaintenanceAdjustment Periodic replacement partsPrint head Customer MaintenanceProduct Life Ink tank target valueSpecial Tools Part 1 1. MaintenanceSerial Number Location List of Error Display / Indication Operator Call Errors by Alarm LED Lit in OrangePage Other Error Messages VbusLow ink Restrictions on paper USB cable not connected Troubleshooting by Symptom When enlarged in the carriage movement direction When enlarged in the paper feed directionPart 1 2. List of Error Display / Indication At replacement After replacementRepair Part 1 3. Repair 3-1. Notes on Service Part Replacement Special Notes on Repair Servicing Side cover L2 and front cover L removalSide cover R2 and front cover R removal Main case removal Scanner flexible cable attachment Timing sensor unit cable wiring Carriage unit flexible cable wiring Power supply unit cable wiringInk tube installation Emblem removal Platen link assemblyPart 1 3. Repair 3-2. Special Notes on Repair Servicing Paper feed motor adjustment Adjustment / SettingsCarriage rail adjustment Document pressure sheet adjustment Front feeder paper feed roller cleaningAmount Part 1 3. REPAIR, 3-3 1 to Ink absorber replacement Ink absorber counter setting User modeService mode See Destination settings procedures below Ink absorber counter value to be set % Part 1 3. Repair 3-3. Adjustment / Settings 6 to Service test print Verification ItemsService test print sample Eeprom information print Print samplePrinted items Part 1 3. Repair Verification ItemsMachine Transportation Part NEW Technologies Cleaning Mode and Amount of INK Purged Part 2 2. Cleaning Mode and Amount of INK Purged Print Mode Normal Color Printing via ComputerBorderless Printing via Computer Normal Grayscale Printing via ComputerManual Duplex Printing via Computer Card / Camera Direct Printing Part 2 3. Print ModeCopying FAQ Problems Specific to the MP510 and Corrective Actions To the table of contents To the top Part 2 4. FAQ Appendix Block Diagram Pixma MP510Signal name Function Input Output Connector Location and PIN LayoutJ301 Print Head 1/3 Carriage Unit Signal name Function Logic Board AssyJ501 LF Encoder Signal name Function J505 Asfpe Sensors Signal name Function Input Output J502 Ink Sensor / Ink Tank Sensor Signal name FunctionJ503 Power Supply Unit Input / Output J507 Main Cam Sensor Signal name Function Input /OutputJ702 LF Motor Signal name Function J701 Carriage Motor Signal name FunctionJ703 Purge Unit Motor Signal name Function J801 Scanner Unit Signal name Function J704 Scanner Motor Signal name FunctionJ901 Memory Card Signal name Function Input Output J902 USB 2.0 I/F Signal name Function Input Output J1 Logic Board Signal name Function Input / Output Card Slot BoardSmgnd J3 CompactFlash Signal name Function J5 IrDA Board Signal name Function Input / Output J301 Memory Card Board Signal name Function Input / OutputJ2 LCD Unit Signal name Function Input / Output Operation Panel BoardSignal name Function Carriage BoardPixma MP510 Specifications Scanner CopyDirect printing DpofPage Print head Supported ink tanks