Canon qy8-13az-000 Adjustment / Settings, Paper feed motor adjustment, Carriage rail adjustment

Page 26

3-3. Adjustment / Settings

(1) Paper feed motor adjustment

Perform the following adjustments when the paper feed motor unit is replaced:

1)When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by the blue arrow in the figure below).

2)After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print operation (due to dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.

Note: The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit. DO NOT loosen them in other cases.

(2) Carriage rail adjustment

Perform the following adjustments when attaching the carriage rail:

1)Before loosening the screws, mark the following positions on the rail:

-Left side: Mark the boss position.

- Right side: Mark the hole position.

2)In attaching the carriage rail, make sure that the left boss and right hole fit to the marks made in step 1) respectively, then fasten the screws.

3)Be sure to perform the confirmation test detailed below; confirm that the print quality is proper and the print head is not contacting the paper.

<Confirmation test>

Using Photo Paper Pro, and with the paper thickness lever set to the left position (normal position), print an image and confirm that the print quality is proper, and the print head is free from contacting the paper.

If the print quality is not proper, or the print head contacts the paper, adjust the head-to-paper distance in the following procedures:

1-21

Image 26

Contents Pixma MP510 Trademarks ScopeRevision Manual Outline II. Table of Contents Part 2 Technical Reference Periodic maintenance MaintenanceAdjustment Periodic replacement partsPrint head Customer MaintenanceProduct Life Ink tank target valueSerial Number Location Part 1 1. MaintenanceSpecial Tools List of Error Display / Indication Operator Call Errors by Alarm LED Lit in OrangePage Other Error Messages VbusLow ink Restrictions on paper USB cable not connected Troubleshooting by Symptom When enlarged in the carriage movement direction When enlarged in the paper feed directionPart 1 2. List of Error Display / Indication Repair After replacementAt replacement Part 1 3. Repair 3-1. Notes on Service Part Replacement Special Notes on Repair Servicing Side cover L2 and front cover L removalSide cover R2 and front cover R removal Main case removal Scanner flexible cable attachment Timing sensor unit cable wiring Carriage unit flexible cable wiring Power supply unit cable wiringInk tube installation Part 1 3. Repair 3-2. Special Notes on Repair Servicing Platen link assemblyEmblem removal Carriage rail adjustment Adjustment / SettingsPaper feed motor adjustment Document pressure sheet adjustment Front feeder paper feed roller cleaningAmount Part 1 3. REPAIR, 3-3 1 to Ink absorber replacement Ink absorber counter setting User modeService mode See Destination settings procedures below Ink absorber counter value to be set % Part 1 3. Repair 3-3. Adjustment / Settings 6 to Service test print Verification ItemsService test print sample Eeprom information print Print samplePrinted items Part 1 3. Repair Verification ItemsMachine Transportation Part NEW Technologies Cleaning Mode and Amount of INK Purged Part 2 2. Cleaning Mode and Amount of INK Purged Print Mode Normal Color Printing via ComputerManual Duplex Printing via Computer Normal Grayscale Printing via ComputerBorderless Printing via Computer Copying Part 2 3. Print ModeCard / Camera Direct Printing FAQ Problems Specific to the MP510 and Corrective Actions To the table of contents To the top Part 2 4. FAQ Appendix Block Diagram Pixma MP510Signal name Function Input Output Connector Location and PIN LayoutJ301 Print Head 1/3 Carriage Unit Signal name Function Logic Board AssyJ501 LF Encoder Signal name Function J505 Asfpe Sensors Signal name Function Input Output J502 Ink Sensor / Ink Tank Sensor Signal name FunctionJ503 Power Supply Unit Input / Output J507 Main Cam Sensor Signal name Function Input /OutputJ703 Purge Unit Motor Signal name Function J701 Carriage Motor Signal name FunctionJ702 LF Motor Signal name Function J901 Memory Card Signal name Function Input Output J704 Scanner Motor Signal name FunctionJ801 Scanner Unit Signal name Function J902 USB 2.0 I/F Signal name Function Input Output J1 Logic Board Signal name Function Input / Output Card Slot BoardSmgnd J3 CompactFlash Signal name Function J5 IrDA Board Signal name Function Input / Output J301 Memory Card Board Signal name Function Input / OutputJ2 LCD Unit Signal name Function Input / Output Operation Panel BoardSignal name Function Carriage BoardPixma MP510 Specifications Scanner CopyDirect printing DpofPage Print head Supported ink tanks