Belkin PM11-EL/RAMA, PM11-UL/RAMA, PM11-EC/RAMA manual Hardware Installation Front Panel Connectors

Page 54

2

Hardware Installation

2.6.22 Front Panel Connectors

Front panel

connectors (J21)

HD-LED: Primary/Secondary IDE LED

This LED will light when the hard drive is being accessed.

G-LED: Green LED

This LED will not light when the system’s power is on or when the system is in the S3 (STR - Suspend To RAM) state. It will light when the system is in the S1 (POS - Power On Suspend) state.

ATX-SW: ATX Power Switch

Depending on the setting in the BIOS setup, this switch is a “dual function power button” that will allow your system to enter the Soft- Off or Suspend mode. Refer to “Soft-Off By PWRBTN” in the Power Management Setup (Chapter 3).

G-SW: Green Switch

This switch will allow your system to enter the Suspend mode.

RESET: Reset Switch

This switch allows you to reboot without having to power off the system thus prolonging the life of the power supply or system.

SPEAKER: Speaker Connector

This connects to the speaker installed in the system chassis.

54

Image 54

Contents PM11-EC/RAMA PM11-EL/RAMA PM11-UL/RAMA 55600206Copyright All Rights ReservedFCC and DOC Statement on Class B Mainboard Table of Contents Supported Softwares Appendix a Using the Suspend toAppendix C Troubleshooting FunctionChipset Features and SpecificationsFeatures ProcessorOnboard Graphics Features Onboard Audio FeaturesOnboard LAN Features PM11-EL/RAMA and PM11-UL/RAMA only IntroductionATX Double Deck Ports PC 99 color-coded connectors ConnectorsOnboard Integrated Media Reader Smart I/O PM11-UL/RAMA only PCI Bus Master IDE Controller IrDA InterfaceUSB Ports Intelligence Dual Function Power ButtonSystem Health Monitor Functions Desktop Management Interface DMIWake-On-Ring Wake-On-LANWake-On-PS/2 Keyboard/Mouse RTC Timer to Power-on the System Wake-On-USB Keyboard/MousePackage Checklist AC Power Failure RecoveryVirus Protection Hardware Installation Mainboard LayoutHardware Installation Supports onboard audio and onboard LANSupports onboard audio, onboard LAN, USB 2.0 and Smart I/O System Memory Hardware Installation Installing the DIM Module Jumper Settings for Clearing Cmos Data Clear Cmos Data Jumper JP2 If you encounter the followingHardware Installation Jumper Settings for Wake-On-PS/2 Keyboard/Mouse On Disable VCC powerWake-On-PS/2 Keyboard/Mouse Jumper JP1 Wake-On-USB 2.0 Keyboard/Mouse J13 and J14 Serial Ports Ports and ConnectorsConnecting the Serial Ports Serial PortHardware Installation Hardware Installation 2 PS/2 Mouse and PS/2 Keyboard Ports PS/2 Mouse PS/2 KeyboardHardware Installation Parallel Port Allows parallel port to operate Setting FunctionStandard Parallel Port One direction only RateHardware Installation Floppy Disk Drive Connector Connecting the Floppy Disk Drive CableHardware Installation IDE Disk Drive Connector Connecting the IDE Disk Drive CableAdding a Second IDE Disk Drive Hardware Installation Universal Serial Bus Ports 6.1 PM11-EC/RAMA and PM11-EL/RAMA6.2 PM11-UL/RAMA USB 1.1 J17 Pin Function UP2Function 5VDul Data+ Ground Key RJ45 LAN Hardware Installation VGA Port VGA PortHardware Installation IrDA Connector Pin FunctionHardware Installation CPU Fan Connector Hardware Installation Chassis Fan Connector On/Off +12V SenseHardware Installation Chip Fan Connector Hardware Installation Game/MIDI Port Front Audio J3 Hardware Installation Audio JacksMic+ Ground Mic Power AuDVcc Avcc AuDROut AuDLOutOnboard Audio Jacks CN3 Connect a microphone to the mic-in jackFront Audio J3 Hardware Installation Internal Audio Connectors Left audio channel Ground Right audio channelAUX-in and CD-in Hardware Installation 16 S/PDIF-out Connector SpdifHardware Installation Smart I/O Connectors PM11-UL/RAMA only Optional Smart I/O Drive Smart Card Interface Pin Function Memory Stick InterfaceSecure Digital Memory Card Interface Hardware Installation Wake-On-LAN Connector +5VSBHardware Installation Wake-On-Ring Connector RI#Hardware Installation Dimm and PCI Standby Power LEDs Dimm Standby Power LEDPCI Standby Power LED Hardware Installation Power Connectors ATX Main Power Connector Pin Function 12V Ground +5V +12V +5V +12V Power Connector Pin Function GroundGround +5V Hardware Installation Front Panel Connectors PWR-LED Power/Standby LED Standard Cmos Features When you press Del, the main menu screen will appearBasic Input/Output System Time Award Bios Setup UtilityDate IDE HDD Auto DetectionCapacity Access ModeIDE Primary/Secondary Master/Slave Drive a and Drive BExtended Memory Halt OnBase Memory Total MemoryAward Bios Setup Utility Advanced Bios Features Virus WarningCPU L2 Cache ECC Checking Quick Power On Self TestCPU L1 & L2 Cache Swap Floppy DriveTypematic Rate Setting Boot Up Floppy SeekBoot Up NumLock Status Typematic Delay MsecOS Select for Dram 64MB Video Bios ShadowSecurity Option Small LogoEPA ShowCurrent FSB Frequency Award Bios Setup Utility Advanced Chipset FeaturesDram Clock/Drive Control Current Dram FrequencySdram CAS Latency Dram ClockDram Timing Bank InterleaveActive to Precharge Tras Dram Command RateAGP Mode Active to CMD TrcdCPU to PCI Write Buffer PCI Delay TransactionAGP Master 1 WS Read PCI Master 0 WS WriteVGA Share Memory Size Options are Enabled and DisabledVideo RAM Cacheable FB Address ConversionVIA OnChip IDE Device Award Bios Setup Utility Integrated PeripheralsIDE Prefetch Mode OnChip IDE Channel 0 and OnChip IDE ChannelVIA OnChip PCI Device VIA-3058 AC97 AudioOnboard LAN PM11-EL/RAMA and PM11-UL/RAMA only SC Port Address/IRQ PM11-UL/RAMA only Onboard FDC ControllerOnboard Serial Port 1 and Onboard Serial Port MS Port Address/IRQ PM11-UL/RAMA onlyUR2 Duplex Mode Uart Mode SelectIR Transmission Delay Use IR PinsECP Mode Use DMA Parallel Port ModeEPP Mode Select Game Port AddressOnChip USB1.1 Controller IDE HDD Block ModeOnboard LAN Boot ROM PM11-EL/RAMA and PM11-UL/RAMA only USB Keyboard SupportAward Bios Setup Utility Power Management Setup Acpi FunctionAcpi Suspend Type Suspend Mode Power Management OptionHDD Power Down Video Off OptionSoft-Off by Pwrbtn Run Vgabios if S3 ResumeModem Use IRQ PWR Lost Resume StateUSB Resume from S3 IRQ/Event Activity DetectPS2KB Wakeup Select PCI MasterResume on Alarm Resume on PCI EventResume On LAN/Ring Date of Month Resume Time hhmmssIRQs Activity Monitoring Reset Configuration Data Award Bios Setup Utility 6 PnP/PCI ConfigurationsPNP OS Installed Resources Controlled ByAssign IRQ for VGA IRQ ResourcesPCI/VGA Palette Snoop Assign IRQ for USBPCI Slot 1 Use IRQ to PCI Slot 3 Use IRQ Award Bios Setup Utility PC Health Status CPU Warning TemperatureThese fields show the voltage of the processor +3.3V, +5V, +12V, -12V, -5V, Vbatv and 5VSBV Auto Detect PCI/DIMM Clk Award Bios Setup Utility Frequency/Voltage ControlCPU Clock Spread SpectrumCPU Clock Ratio This field is used to select the CPU’s frequency ratioAward Bios Setup Utility Load Fail-Safe Defaults Load Optimized DefaultsAward Bios Setup Utility Set Supervisor Password Set User PasswordUpdating the Bios Award Bios Setup Utility Save & Exit SetupExit Without Saving Desktop Management Interface DMI Running the DMI UtilitySupported Software Using the DMI Utility Edit DMISupported Software Add DMI Load DMI FileSave DMI File VIA Service Pack Hardware MonitorSupported Software VIA Service Pack Installation Notes Audio Drivers and Software Applications Graphics Drivers VIA USB 2.0 Driver PM11-UL/RAMA onlyWinbond Smart I/O Drivers PM11-UL/ Rama only Drivers and Utilities Installation Notes Microsoft DirectX 8.1 DriverAppendix a Using the Suspend to RAM Function Using the Suspend to RAM FunctionUsing the Suspend to RAM Function 101 102 Error Messages Cmos battery is no longer functional. It should be replacedPost Beep System Error Message Troubleshooting Checklist Monitor/DisplayTroubleshooting Power SupplyFloppy Drive Troubleshooting Hard Drive Hard disk failureTroubleshooting Serial Port KeyboardMainboard