SATO D512, D508 service manual Barcodes

Page 10

Section 1: Introduction

1.1 GENERAL SPECIFICATIONS (CONT’D)

 

Barcodes

 

SYMBOLOGIES

 

Supported 1D formats

UPC-A/E

(excluding customized barcode

EAN-8/EAN-13

addressing in firmware)

CODABAR

 

CODE39

 

CODE93

 

CODE128

 

UCC/EAN128

 

Interleaved 2 of 5

 

Industrial 2 of 5

 

Matrix 2of5

 

RSS Composite

 

MSI

 

POSTNET

 

Bookland

Supported 2D formats

PDF 417

 

Micro PDF 417

 

Truncated PDF 417

 

Maxicode

 

Data Matrix

 

QR Code

Ratios

1:2, 1:3, 2:5 User definable bar widths (depending on software)

Bar Height

4 to 600 dots (depending on software)

Rotation

0°, 90°, 180° and 270° (depending on software)

 

*All specifications subject to change without notice.

 

Physical Attributes

 

DIMENSIONS

 

 

Width

 

7.8 in. (198 mm)

Depth

 

9.1 in. (230 mm)

Height

 

6.6 in. (167 mm)

Weight

 

5.5 lbs (2.5 Kg) excluding AC adaptor

 

 

 

POWER REQUIREMENTS

 

 

Voltage

 

USA: AC 115 V (+/- 10 %)

 

 

50/60 Hz (+/-1%)

Power Consumption

 

67W nominal

 

 

 

ENVIRONMENTAL

 

 

Operating

 

32° to 95°F (0° to 35°C),

 

 

30 to 80% RH, non-condensing

Storage

 

23° to 140°F (-5° to 60°C),

 

 

30-90% RH, non-condensing

 

 

 

REGULATORY APPROVALS

 

 

Safety

 

USA : UL(UL60950-1)

 

 

CANADA : C-UL(CSA C22.2 No.60950-1-3)

EMC/EMS

 

USA : FCC15B (ClassB)

 

 

 

 

 

 

SATO D508/D512 Operator Manual

Page 1-6

Image 10
Contents OperatorSvice Manual Sato America, Inc Table of Contents Sato Contacts TroubleshootingSato Group of companies Overview General Printer Specifications IntroductionGeneral Printer Specifications AttributeGeneral Specifications CONT’D MediaAttributes Barcodes Optional Accessories Introduction Sato D508/D512 Operator Manual Installation Printer Placement Tips Electrical PrecautionsGeneral Precautions Unpacking Printer Part Names Setting UP the Printer Follow these steps to set up your printerLoading Media Fanfold media Label Sensing Overview of the fanfold-paper loading pathThis page is left blank intentionally Operating Panel Rear Panel Configuration Panel DIP Switch SettingsDIP Switch Settings CONT’D Switch 4 UnusedSwitch 7 Data Dump Switch 8 Unused Error Codes Mode Length of Offset mm Print head resolution OffsetsOriginal First Line Print Position Potentiometer AdjustmentsPitch Offset Moved with Leading Edge Positive + OffsetPotentiometer Adjustments CONT’D Print DarknessData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints Configuration and Operation Sato D508/D512 Operator Manual Adjusting the Print Quality IntroductionCleaning the Print HEAD, Platen and Rollers Cleaning the Print HEAD, Platen and Rollers CONT’D RELEASING/REPLACING the Print Head Cleaning the Sensor This page is left blank intentionally Interface Specifications Interface TypesReceive Buffer Single Job BufferReceive Buffer CONT’D Multi Job BufferPIN Signal Direction IEEE1284 Parallel InterfaceGeneral Specifications RS-232C Interface1 RS-232C Interface Signals Pin Direction Signal DefinitionUniversal Serial BUS Interface READY/BUSY Flow ControlON/X-OFF Flow Control Local Area Network InterfaceSpecifications Wireless LAN Interface 802.11 B/GSwitch Setting LED Indicator Status Software SpecificationsInterface Specifications Checking the IEEE1284 Parallel Interface Initial ChecklistObservations Using the IEEE1284 Parallel Interface CONT’D Checking Using the Parallel Interface CONT’D ObserationsChecking the RS232C Serial Interface Error Signals LED Indicators Buzzer Error Condition Corrective ActionChecking the 802.11G Wireless Interface Sato Contacts Sato Group of Companies Asia Pacific & Oceania Region