SATO D512, D508 service manual General Specifications CONT’D, Media

Page 8

Section 1: Introduction

1.1 GENERAL SPECIFICATIONS (CONT’D)

 

Attribute

 

 

MEDIA

 

Media Type

Roll and fanfold

Label Thickness

0.0026” (0.6 mm*) - 0.007” (* 0.19 mm)

(Label + backing paper)

*Check with your dealer regarding conditions

 

for using thin 0.002” (06 mm) labels

Label Form

Roll Label: Maximum outer diameter of 4.33” (110 mm) face out

 

Core Inner Diameter of 1.5” (40 mm)

 

Outer Diameter: 4.33” (110 mm)

 

Fan-fold label: Max. foldable height: 3.94” (100 mm) loaded externally)

 

Wind Orientation: Face-out

Label Size (adhesive labels)

Width for all types:

 

1.1” (28 mm) - 4.65” (118 mm)

 

For continuous feed:

 

Length: 0.71” (18 mm) - 15.75” (400 mm)

 

For Cutter usage (optional):

 

Length: 1.1” (23 mm) - 15.75” (400 mm)

 

For Tear Off mode:

 

Length: 0.71” (18 mm) - 15.75” ( 400 mm)

 

 

SENSING

 

See-Through

For die-cut label with gap: Fixed, 0.25" (6.3 mm) from left label edge

Continuous Form

Sensor not used

Eye Mark

Reflective sensor (for use with Pre-printed eye marks)

*All specifications subject to change without notice.

Page 1-4

SATO D508/D512 Operator Manual

Image 8
Contents OperatorSvice Manual Sato America, Inc Table of Contents Sato Group of companies TroubleshootingSato Contacts Overview General Printer Specifications IntroductionGeneral Printer Specifications AttributeGeneral Specifications CONT’D MediaAttributes Barcodes Optional Accessories Introduction Sato D508/D512 Operator Manual Installation Printer Placement Tips Electrical PrecautionsGeneral Precautions Unpacking Printer Part Names Setting UP the Printer Follow these steps to set up your printerLoading Media Fanfold media Label Sensing Overview of the fanfold-paper loading pathThis page is left blank intentionally Operating Panel Rear Panel Configuration Panel DIP Switch SettingsDIP Switch Settings CONT’D Switch 4 UnusedSwitch 7 Data Dump Switch 8 Unused Error Codes Mode Length of Offset mm Print head resolution OffsetsPotentiometer Adjustments Pitch OffsetOriginal First Line Print Position Moved with Leading Edge Positive + OffsetPotentiometer Adjustments CONT’D Print DarknessData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints Configuration and Operation Sato D508/D512 Operator Manual Adjusting the Print Quality IntroductionCleaning the Print HEAD, Platen and Rollers Cleaning the Print HEAD, Platen and Rollers CONT’D RELEASING/REPLACING the Print Head Cleaning the Sensor This page is left blank intentionally Interface Specifications Interface TypesReceive Buffer Single Job BufferReceive Buffer CONT’D Multi Job BufferPIN Signal Direction IEEE1284 Parallel InterfaceGeneral Specifications RS-232C Interface1 RS-232C Interface Signals Pin Direction Signal DefinitionREADY/BUSY Flow Control ON/X-OFF Flow ControlUniversal Serial BUS Interface Local Area Network InterfaceSwitch Setting Wireless LAN Interface 802.11 B/GSpecifications LED Indicator Status Software SpecificationsInterface Specifications Observations Initial ChecklistChecking the IEEE1284 Parallel Interface Using the IEEE1284 Parallel Interface CONT’D Checking Using the Parallel Interface CONT’D ObserationsChecking the RS232C Serial Interface Error Signals LED Indicators Buzzer Error Condition Corrective ActionChecking the 802.11G Wireless Interface Sato Contacts Sato Group of Companies Asia Pacific & Oceania Region