SATO D512, D508 service manual DIP Switch Settings CONT’D, Switch 4 Unused

Page 26

Section 3: Configuration and Operation

Switches 1–3: Paper Handling settings These three switches select the method used for controlling paper handling:

Continuous mode - (default mode) Does not use the sensor for paper indexing. The paper movement will stop after all the label data has been printed.

Tear Off mode - Paper is fed out to the cut/tear off position after printing is complete. Before the next label is printed, the paper is pulled back in to the first print line position.

Cutter mode - Enables the Cutter option if installed.

3.3 DIP SWITCH SETTINGS (CONT’D)

Switches 1–3: Font/Graphic loading settings Enables the loading of fonts and/or graphics into printer memory for faster retrieval.

 

DSW1

DSW2

DSW3

Mode

 

 

 

 

 

 

 

 

Off

Off

Off

Continuous

 

 

On

Off

Off

Tear Off

 

 

Off

On

Off

Cutter

 

 

 

 

 

 

 

 

On

Off

On

Reserved

 

 

 

 

 

 

 

 

Off

On

On

Load Font

 

 

 

 

 

 

 

Configuration Switch

ON

OFF

1 2 3 4 5 6 7 8

DSW1 DSW2 DSW3

Mode

Off

On

On

Load Font

Switch 4: Unused

This switch is reserved for future use.

Configuration Switch

ON

OFF

1 2 3 4 5 6 7 8

DSW4 Mode

Off DT

-Reserved

Configuration Switch

ON

OFF

1 2 3 4 5 6 7 8

Page 3-4

SATO D508/D512 Operator Manual

Image 26
Contents OperatorSvice Manual Sato America, Inc Table of Contents Sato Group of companies TroubleshootingSato Contacts Overview General Printer Specifications IntroductionGeneral Printer Specifications AttributeGeneral Specifications CONT’D MediaAttributes Barcodes Optional Accessories Introduction Sato D508/D512 Operator Manual Installation Printer Placement Tips Electrical PrecautionsGeneral Precautions Unpacking Printer Part Names Setting UP the Printer Follow these steps to set up your printerLoading Media Fanfold media Label Sensing Overview of the fanfold-paper loading pathThis page is left blank intentionally Operating Panel Rear Panel Configuration Panel DIP Switch SettingsDIP Switch Settings CONT’D Switch 4 UnusedSwitch 7 Data Dump Switch 8 Unused Error Codes Mode Length of Offset mm Print head resolution OffsetsOriginal First Line Print Position Potentiometer AdjustmentsPitch Offset Moved with Leading Edge Positive + OffsetPotentiometer Adjustments CONT’D Print DarknessData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints Configuration and Operation Sato D508/D512 Operator Manual Adjusting the Print Quality IntroductionCleaning the Print HEAD, Platen and Rollers Cleaning the Print HEAD, Platen and Rollers CONT’D RELEASING/REPLACING the Print Head Cleaning the Sensor This page is left blank intentionally Interface Specifications Interface TypesReceive Buffer Single Job BufferReceive Buffer CONT’D Multi Job BufferPIN Signal Direction IEEE1284 Parallel InterfaceGeneral Specifications RS-232C Interface1 RS-232C Interface Signals Pin Direction Signal DefinitionUniversal Serial BUS Interface READY/BUSY Flow ControlON/X-OFF Flow Control Local Area Network InterfaceSwitch Setting Wireless LAN Interface 802.11 B/GSpecifications LED Indicator Status Software SpecificationsInterface Specifications Observations Initial ChecklistChecking the IEEE1284 Parallel Interface Using the IEEE1284 Parallel Interface CONT’D Checking Using the Parallel Interface CONT’D ObserationsChecking the RS232C Serial Interface Error Signals LED Indicators Buzzer Error Condition Corrective ActionChecking the 802.11G Wireless Interface Sato Contacts Sato Group of Companies Asia Pacific & Oceania Region