SATO D508, D512 service manual Attributes

Page 9

Section 1: Introduction

1.1 GENERAL SPECIFICATIONS (CONT’D)

	Attributes
CONTROLS AND SIGNALS
On-Line LED	Green
Power LED	Green
Error LED	Red
LED Display Panel	7-Segment Single Character
On/Off-Line Button	Front Panel
Label Feed Button	Front Panel
Power On/Off Button	Front Panel
Self Diagnostics	Head check
	Paper end
	Cover open
	Test print
POTENTIOMETER ADJUSTMENTS
Adjustment Potentiometers	VR1: Offset level (DIPSW6 = OFF)
	VR1: Print darkness (DIPSW6 = ON)
	VR2: Eye Mark
	VR3: Gap sensor (to adjust the threshold)
	VR4: Label pitch offset
DIP switches	DIP-SW -1,2,3 : Operation mode(Print mode/Download mode)
	DIP-SW -4 : Reserved (constantly OFF)
	DIP-SW -5 : Head check (ON-Enabled / OFF-Disabled)
	DIP-SW -6 : VR1 function switch
	(ON-Print darkness level / OFF-Offset)
	DIP-SW -7 : DATA dump (ON-HEX dump print / OFF-Normal print)
	DIP-SW -8 : Reserved (constantly OFF)

INTERFACE CONNECTIONS
Parallel (Option)	IEEE1284
Serial (Option)	RS232C (up to 57.6K bps) Hardware Flow Control (Ready/Busy) Soft-
	ware Flow Control (X-On/X-Off)
	Bi-directional Status
USB (Option)	USB Specification Version 1.1
LAN (Option)	10/100 Base-T
RFID (Option)	TBA
Wireless LAN (Option)	802.11 b/g (internal)

*All specifications subject to change without notice.

SATO D508/D512 Operator Manual

Page 1-5

Image 9

Contents OperatorSvice Manual Sato America, Inc Table of Contents Troubleshooting Sato ContactsSato Group of companies Overview Introduction General Printer SpecificationsAttribute General Printer SpecificationsMedia General Specifications CONT’DAttributes Barcodes Optional Accessories Introduction Sato D508/D512 Operator Manual Installation Electrical Precautions Printer Placement TipsGeneral Precautions Unpacking Printer Part Names Follow these steps to set up your printer Setting UP the PrinterLoading Media Fanfold media Overview of the fanfold-paper loading path Label SensingThis page is left blank intentionally Operating Panel Rear Panel DIP Switch Settings Configuration PanelSwitch 4 Unused DIP Switch Settings CONT’DSwitch 7 Data Dump Switch 8 Unused Error Codes Offsets Mode Length of Offset mm Print head resolutionPitch Offset Potentiometer AdjustmentsOriginal First Line Print Position Moved with Leading Edge Positive + OffsetPrint Darkness Potentiometer Adjustments CONT’DData Dump Diagnostic Label Printing Test Labels Printing FACTORY/SERVICE Test Prints Configuration and Operation Sato D508/D512 Operator Manual Introduction Adjusting the Print QualityCleaning the Print HEAD, Platen and Rollers Cleaning the Print HEAD, Platen and Rollers CONT’D RELEASING/REPLACING the Print Head Cleaning the Sensor This page is left blank intentionally Interface Types Interface SpecificationsSingle Job Buffer Receive BufferMulti Job Buffer Receive Buffer CONT’DIEEE1284 Parallel Interface PIN Signal DirectionRS-232C Interface General SpecificationsPin Direction Signal Definition 1 RS-232C Interface SignalsON/X-OFF Flow Control READY/BUSY Flow ControlUniversal Serial BUS Interface Local Area Network InterfaceWireless LAN Interface 802.11 B/G SpecificationsSwitch Setting Software Specifications LED Indicator StatusInterface Specifications Initial Checklist Checking the IEEE1284 Parallel InterfaceObservations Using the IEEE1284 Parallel Interface CONT’D Obserations Checking Using the Parallel Interface CONT’DChecking the RS232C Serial Interface LED Indicators Buzzer Error Condition Corrective Action Error SignalsChecking the 802.11G Wireless Interface Sato Contacts Asia Pacific & Oceania Region Sato Group of Companies