SATO 5900RVe manual IEEE1284 Parallel Interface, Specifications, Ack, Init

Page 21

Unit 3: Installation

IEEE1284 PARALLEL INTERFACE

The parallel interface is a Plug-In Interface Module that can be installed by the user. It conforms to the IEEE1284 specification. It will automatically detect the IEEE1284 signals and operate in the high speed mode. If it does not detect the IEEE1284 signals, it will operate in the standard Centronics mode, which is significantly slower. For this reason, an interface cable and host interface conforming to the IEEE1284 specification must be present to fully utilize the speed capabilities. This interface also operates bi-directionally and can report the status of the printer back to the host.

 

SPECIFICATIONS

Printer Connector

AMP 57-40360 DDK (or equivalent)

Cable Connector

AMP 57-30360 DDK (or equivalent)

Cable

IEEE1284 Parallel, 10 ft. (3 m) or less

Signal Level

High = +2.4V to +5.0V, Low = 0V to -0.4V

Data Stream

<ESC>A . . Job#1 . . <ESC>Z<ESC>A . . Job#n . . <ESC>Z

NOTE: Pin assignments begin with one (1) in the upper right corner and descend to eighteen (18) in the upper left corner. Pin number nineteen (19) picks up in the lower right corner and descends to thirty-six (36) in the lower left.

IEEE 1284 PARALLEL INTERFACE PIN ASSIGNMENTS

PIN

SIGNAL

DIRECTION

PIN

SIGNAL

DIRECTION

1

Strobe

To Printer

19

Strobe Return

Reference

2

Data 1

To Printer

20

Data 1 Return

Reference

3

Data 2

To Printer

21

Data 2 Return

Reference

4

Data 3

To Printer

22

Data 3 Return

Reference

5

Data 4

To Printer

23

Data 4 Return

Reference

6

Data 5

To Printer

24

Data 5 Return

Reference

7

Data 6

To Printer

25

Data 6 Return

Reference

8

Data 7

To Printer

26

Data 7 Return

Reference

9

Data 8

To Printer

27

Data 8 Return

Reference

10

ACK

To Host

28

ACK Return

Reference

11

Busy

To Host

29

Busy Return

Reference

12

Ptr Error

To Host

30

PE Return

Reference

13

Select

To Host

31

INIT

From Host

14

AutoFD1

To Host

32

Fault

To Host

15

Not Used

 

33

Not Used

 

16

Logic Gnd

 

34

Not Used

 

17

FG

Frame Gnd

35

Not Used

 

18

+5V (z=24k ohm)

To Host

36

SelectIn1

From Host

1 Signals required for ieee 1284 mode.

SATO M5900RVe Operator Manual

PN 9001125A

Page 3-7

Image 21
Contents M5900RVe Direct Thermal Printer Sato America, Inc Table of Contents Troubleshooting MaintenanceOperation Introduction Result in Presonal Injury About this Manual1a, Primary Components General Description1b, Primary Components Switches Control FeaturesPage Technical Data Power Physical CharacteristicsEnvironmental PrintCharacter Font Capabilities Character Control Downloadable FontsBAR Code Capabilties Regulatory ApprovalsInstallation Packed Components Unpacking & Parts IdentificationSite Location Printer InstallationMedia Selection Media LoadingMedia Loading RS232C Specifications Interface SelectionRS232 Serial Interface PIN Direction Signal Definition RS232C Serial Interface SignalsCable Requirements DB9 Host Connection DB9 PrinterIEEE1284 Parallel Interface SpecificationsACK Init80211B Wireless Specifications 802.11B WirelessUniversal Serial BUS USB Adapter Local Area Network LAN EthernetACK/NAK Protocol Receive BufferInterface Module Upgrade Accessories InstallationOperation DIP Switch Panels Printer ConfigurationDSW1 Configuration DSW1 Default SettingsDSW1 Function Descriptions OFFDSW2 Configuration DSW1 DSW2 Default SettingsConfiguration DSW2 Function DescriptionsFunction Description DSW3 Default SettingsNormal Mode Configuration ModesTest Print Mode Test Print ModeAdvanced Mode Advanced ModeDefault Settings Mode Default Settings ModeDownload Font Deletion Status Description Acsii HEX Transfer Flash Memory Download ModeFlash Memory Download Mode User Download Mode User Download ModeHex Dump Mode HEX Dump ModeCard Mode Card ModeNon-Standard Clear Mode NON-STANDARD Clear Mode10, Service Mode Service Mode11, Counters Mode Counters ModeMaintenance Mode Maintenance ModeAdvanced Mode Card ModeMenu Description Service Mode Counters Mode Maintenance Mode Potentiometer DESCRIPTION/PROCEDURE Operational AdjustmentsPrint OffsetFeed Direction 14, Sensor & Accessory Locations Unit 4 Operation Sato M5900RVe Operator Manual PN 9001125A Troubleshooting LCD Message Beep Error Condition To Clear Light Print Images Image VoidsUneven Print Darkness Smeared Print ImagesMeandering Media Printer Creates a Blank LabelIncorrect Label Positioning Troubleshooting Procedures Parallel Interface Universal Serial BUS USB InterfaceLAN Ethernet Interface Page Maintenance From the PRINTER, Exersize Care to Prevent Print Head Damage Cleaning ProceduresFuse Replacement Replacement ProceduresPrint Head to Prevent Damage to ITS Elements Print Head ReplacementInterface Board Replacement Interface Board ReplacementPrint Defects Relative Procedure Adjustment ProceduresPrint Head Balance Adjustment Print Head Balance AdjustmentPrint Head Alignment Print Head Alignment