SATO 5900RVe manual Maintenance Mode

Page 42

Unit 4: Operation

MAINTENANCE MODE

The Maintenance Mode encompasses the Factory and All Clear Modes.

DSW2-4 = ON
LINE + FEED	LINE/FEED
+ POWER	LINE/FEED
+ POWER	Alternately
	Alternately
		Scrolls
	When LINE is
Printer beeps.	pressed.			FEED
	Processes and			FEED
	advances when
		FEED is
		pressed.
			ALL CLEAR
MAINTENANCE MODE			COUNTER		EEPROM
DIPSW2-4 ON->OFF	COUNTER CLEAR
	COUNTER CLEAR
			LINE/FEED
DSW2-4 = OFF	PRINT SIZE		Alternately
DSW2-4 = OFF

	SMALL	LARGE
				Scrolls
			When LINE is
FACTORY MODE	TEST PRINT		pressed.
	TEST PRINT		Processes and
	PRESS FEED KEY		Processes and
	PRESS FEED KEY		advances when
			advances when
			FEED is
			pressed.
LINE		FEED
LINE			XXXXXXX ALLCLEAR
			XXXXXXX ALLCLEAR
			YES		NO
ALL CLEAR MODE
		Printer	XXXXXXX ALLCLEAR
LINE		beeps three	XXXXXXX ALLCLEAR
LINE		beeps three	COMPLETED
		times.	COMPLETED
		times.
		FEED

Figure 12, Maintenance Mode

SATO M5900RVe Operator Manual

PN 9001125A

Page 4-18

Image 42

Contents M5900RVe Direct Thermal Printer Sato America, Inc Table of Contents Troubleshooting MaintenanceOperation Introduction About this Manual Result in Presonal InjuryGeneral Description 1a, Primary Components1b, Primary Components Control Features SwitchesPage Technical Data Environmental Physical CharacteristicsPower PrintCharacter Font Capabilities BAR Code Capabilties Downloadable FontsCharacter Control Regulatory ApprovalsInstallation Unpacking & Parts Identification Packed ComponentsMedia Selection Printer InstallationSite Location Media LoadingMedia Loading RS232C Specifications Interface SelectionRS232 Serial Interface Cable Requirements DB9 RS232C Serial Interface SignalsPIN Direction Signal Definition Host Connection DB9 PrinterACK SpecificationsIEEE1284 Parallel Interface InitUniversal Serial BUS USB Adapter 802.11B Wireless80211B Wireless Specifications Local Area Network LAN EthernetReceive Buffer ACK/NAK ProtocolAccessories Installation Interface Module UpgradeOperation Printer Configuration DIP Switch PanelsDSW1 Function Descriptions DSW1 Default SettingsDSW1 Configuration OFFConfiguration DSW2 Default SettingsDSW2 Configuration DSW1 DSW2 Function DescriptionsDSW3 Default Settings Function DescriptionConfiguration Modes Normal ModeTest Print Mode Test Print ModeAdvanced Mode Advanced ModeDefault Settings Mode Default Settings ModeFlash Memory Download Mode Download Font Deletion Status Description Acsii HEX TransferFlash Memory Download Mode User Download Mode User Download ModeHEX Dump Mode Hex Dump ModeCard Mode Card ModeNON-STANDARD Clear Mode Non-Standard Clear ModeService Mode 10, Service ModeCounters Mode 11, Counters ModeMaintenance Mode Maintenance ModeAdvanced Mode Card ModeMenu Description Service Mode Counters Mode Maintenance Mode Print Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE OffsetFeed Direction 14, Sensor & Accessory Locations Unit 4 Operation Sato M5900RVe Operator Manual PN 9001125A Troubleshooting LCD Message Beep Error Condition To Clear Uneven Print Darkness Image VoidsLight Print Images Smeared Print ImagesMeandering Media Printer Creates a Blank LabelIncorrect Label Positioning Troubleshooting Procedures Universal Serial BUS USB Interface Parallel InterfaceLAN Ethernet Interface Page Maintenance Cleaning Procedures From the PRINTER, Exersize Care to Prevent Print Head DamageReplacement Procedures Fuse ReplacementPrint Head Replacement Print Head to Prevent Damage to ITS ElementsInterface Board Replacement Interface Board ReplacementAdjustment Procedures Print Defects Relative ProcedurePrint Head Balance Adjustment Print Head Balance AdjustmentPrint Head Alignment Print Head Alignment