SATO M-84PRO Printer DIP Switch Configuration, DIP Switch Panels, RS232 TRANSMIT/RECEIVE Setting

Page 27

SECTION 3.

CONFIGURATION

PRINTER DIP SWITCH CONFIGURATION

DIP SWITCH PANELS

There are two DIP switches (DSW2 and DSW3) located on the front panel under a protective cover. In addition, a third DIP switch is located on the RS232C Serial Adapter card and is used to set the RS232C transmit/receive parameters. These switches can be used to set:

•Thermal transfer or direct thermal mode

•Label sensor enable/disable

•Head check mode

•Hex dump mode

•Single Job or Multi-Job Receive buffer

•Operation mode

Each switch is an eight section toggle switch. The ON position is always up. To set the switches, first power the unit Off, then position the DIP switches. Finally, after placing the switches in the desired positions, power the printer back on. The switch settings are read by the printer electronics during the power up sequence. They will not become effective until the power is cycled.

RS232 TRANSMIT/RECEIVE SETTING

Data Bit Selection (DSW1-1).This switch sets the printer to receive either 7 or 8 bit data bits for each byte transmitted.

 

 

 

 

 

DSW1-1

SETTING

 

 

 

 

 

 

 

 

 

 

Off

8 Data Bits

 

 

 

 

 

 

On

7 Data Bits

 

 

 

 

 

 

 

 

 

DSW1

ON

OFF

1 2 3 4 5 6 7 8

Parity Selection (DSW1-2,DSW1-3.These switches select the type of parity used for error detection.

 

 

 

 

 

DSW1

 

DSW1-1

DSW1-3

SETTING

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off

Off

No Parity

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

Off

On

Even

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On

Off

Odd

 

 

1 2 3 4 5 6 7 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On

On

Not Used

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SATO M-84PRO

PN 9001105 Rev. A

Page 3-1

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 84PRO Page Table of Contents Interface Specifications Introduction Section Printer OverviewSpecification General Printer Specifications84PRO All Models Matrix Fonts Character FontsBAR Code BAR CodesPhysical PowerAccessories and Options Optional AccessoriesThis page left intentionally blank Section Installation Unpacking and Parts Identification Setting UP the Printer LCD Loading Labels and Tags Installation Route Labels Under Guide Head Latch Loading the Ribbon Tape Operator Panel DSW On LineLine FeedRear Panel Sensors Head Open SensorLabel Indexing Sensor This page left intentionally blank OFF Printer DIP Switch ConfigurationDIP Switch Panels RS232 TRANSMIT/RECEIVE SettingDSW2 OFF Printer SET UPHex Dump Selection DSW2-4.Selects Hex Dump mode see DSW3 DSW3 OFF SettingDSW3-6 DSW3-7 Default Completed Default SettingsSwitch Selections Software Default SettingsPotentiometer Adjustments PitchBackfeed Offset Print DisplayInitializing Online QTY000000 LCD Panel Printer ConfigurationNormal Mode Mode KEY Sequence Initial DisplayPrint Speed Print DarknessPitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Initializing Advanced ModeSET Calendar YES no Print OffsetIgnore CR/LF YES no CalendarCard Mode Character Pitch Prop Fixed Advanced ModeCopy Start YES no Truetype Fontcopy Completed Card COPY/FORMAT Xxxxxxx Error CARD-MEMORY Copy Copying MEMORY-CARDCOPY Program Y/N Initializing Advanced Mode Service Mode GAP Input Service ModeGAP Input EYE Input Auto Online Feed YES no Feed on Error EXT PIN 9 Select MODE1 MODE2 Euro Code Reprint W/FEED YES noLabel RE-DETECT Enable Disable Counters HD CUT Life Head Counter Head Count Clear YES no Counters ModeTest Print Mode Advanced Mode Counters ModeTest Print Size Default Setting ModeTest Print Mode Configuration Initializing Default Setting YES noInitializing User Download Press the Line KEY Default Setting CompletedClear NON-STANDARD Protocol Download User Defined Protocol CodesHEX Dump Mode User Download WaitingInitializing Online Print Darkness Adjusting the Print QualityPrint Speed Cleaning the Print HEAD, Platen and RollersCleaning the Platen and Rollers Cleaning the Label Edge SensorsSupplies needed Flat blade screwdriver Replacing the Print HeadDo not remove the two outside Screws painted red on either This page left intentionally blank Using the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceUsing the LAN Ethernet Interface Using the Universal Serial BUS USB InterfaceChecking the Network Connection and Cabling Troubleshooting LED LCD Message Audible Error Possible Causes Beep Condition Error SignalsInterface Types Section Interface SpecificationsReceive Buffer Single JOB BufferMulti JOB Buffer IEEE1284 Parallel Interface Data Streams Electrical SpecificationsRS232 Serial Interface General SpecificationsPIN Assignments ON/X-OFF Flow Control Cable Requirements READY/BUSY Flow ControlUniversal Serial BUS USB Interface Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications Print JOB Cancel canENQUIRE/ACK/NAK Enquire ENQPrint Start DC1 Print Stop DLEInstallation Error HandlingPcmcia Memory Cards Description PLUG-IN Interface Modules Error Description Indication RemedyOperator Setup CutterGeneral Operation Label Dispense Option Removing and Unwinding the Roll Label RewinderReal Time Clock

M-84PRO specifications

The SATO M-84PRO is a high-performance thermal printer designed for industrial applications, known for its reliability and efficiency in various labeling tasks. This printer is a part of SATO's esteemed M-84 series, which combines advanced technology with user-friendly design to meet the demands of large-scale operations.

One of the standout features of the SATO M-84PRO is its fast printing speed, capable of producing labels at a rate of up to 8 inches per second. This rapid output makes it an ideal choice for environments that require quick turnaround times, such as warehouses, manufacturing lines, and logistics centers.

The M-84PRO employs a direct thermal or thermal transfer printing method, allowing for outstanding print quality. With a maximum print resolution of 305 dpi, it ensures crisp and clear text and graphics, which is essential for barcodes and detailed images on labels. The printer supports a wide range of media types, accommodating label widths from 0.75 inches to 4.1 inches, making it versatile for various labeling needs.

Equipped with SATO's unique Smart Technology, the M-84PRO offers enhanced control over label production. This technology includes automatic label detection and calibration, which minimizes setup time and reduces waste, thus improving overall operational efficiency. Additionally, the printer is compatible with various programming languages, including SAPscript and ZPL, ensuring easy integration into existing systems.

Durability is another hallmark of the M-84PRO. Built with robust materials, it can withstand the rigors of industrial environments, ensuring long-term performance. The printer also features a compact design, which is perfect for tight workspaces, while still being rugged enough to handle demanding tasks.

Moreover, the SATO M-84PRO boasts extensive connectivity options, including USB, Ethernet, and serial interfaces, which allow for seamless integration into any operational workflow. It also supports various operating systems, providing flexibility and ease of use when working with different platforms.

The printer’s user-friendly interface, highlighted by an LCD panel and multi-functional buttons, facilitates easy navigation and operation. Maintenance is also simplified, thanks to modular components that allow for quick and easy replacement of parts when necessary.

In summary, the SATO M-84PRO stands out as a leading choice in the thermal printer market, combining high-speed printing, excellent durability, and versatile labeling capabilities. Its advanced technologies and features make it suitable for a variety of demanding applications, ensuring that businesses can rely on it for their labeling needs.
Top Page Image Contents