SATO M-84PRO manual Test Print Mode, Advanced Mode Counters Mode, Initializing

Page 51

Section 3. Configuration

COUNTERS MODE

The Counters Mode is provided to allow the user to access the internal printer cousters.

ADVANCED MODE

COUNTERS MODE

The Counter Mode is accessed from the Advanced Mode. Press the LINE key to step to the Counter Mode.

Pressing the FEED key will advance the display to the counter selections.

COUNTERS

HD CUT LIFE

HEAD COUNTER

0.5M

HEAD COUNT CLEAR

YES NO

The counters are identified in the display as:

HD: Head Counter (should be reset when print head is replaced)

CUT: Cutter Counter

LIFE: Life Counter (cannot be reset)

1.Use the LINE key to step the cursor to the desired counter, the Head (HD) counter or the LIFE counter. The default position is the Head Counter.

2.Once the correct setting is selected, pressing the FEED key will display the current value (in meters) stored in the counter. The maximum number of digits displayed is 8.

3.Pressing the FEED key again will advance the counter to the Clear mode. All counters with the exception of the LIFE counter may be cleared.

4.Use the LINE key to select the desired setting. If you only wanted to read the counter value, select NO. If you want to read the counter and reset it to 0.0, place the cursor over the YES. Once the desired setting is selected, pressing the FEEDkey will advance the return you to the Counters Mode display.

COUNTERS MODE

5.To exit the Counters Mode, turn power to the printer off and then back on.

TEST PRINT MODE

The Test Print Mode offers 4 different status labels for troubleshooting. If DSW3-5 is in the OFF position, the Test Print cycle must be initiated with a Print Start signal on the EXT connector You enter the Test Print Mode by pressing the FEED key while powering the printer on..

V05.00.03.00

INITIALIZING

Displays the firmware during the initialization.

SATO M-84PRO

PN 9001105 Rev. A

Page 3-25

Page 50 Page 52
Image 51
Page 50 Page 52
Contents 84PRO Page Table of Contents Interface Specifications Introduction Section Printer OverviewSpecification General Printer Specifications84PRO All Models Matrix Fonts Character FontsBAR Code BAR CodesPhysical PowerAccessories and Options Optional AccessoriesThis page left intentionally blank Section Installation Unpacking and Parts Identification Setting UP the Printer LCD Loading Labels and Tags Installation Route Labels Under Guide Head Latch Loading the Ribbon Tape Operator Panel DSW On LineLine FeedRear Panel Sensors Head Open SensorLabel Indexing Sensor This page left intentionally blank OFF Printer DIP Switch ConfigurationDIP Switch Panels RS232 TRANSMIT/RECEIVE SettingDSW2 OFF Printer SET UPHex Dump Selection DSW2-4.Selects Hex Dump mode see DSW3 DSW3 OFF SettingDSW3-6 DSW3-7 Default Completed Default SettingsSwitch Selections Software Default SettingsPotentiometer Adjustments PitchBackfeed Offset Print DisplayInitializing Online QTY000000 LCD Panel Printer ConfigurationNormal Mode Mode KEY Sequence Initial DisplayPrint Speed Print DarknessPitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Initializing Advanced ModeSET Calendar YES no Print OffsetIgnore CR/LF YES no CalendarCard Mode Character Pitch Prop Fixed Advanced ModeCopy Start YES no Truetype Fontcopy Completed Card COPY/FORMAT Xxxxxxx Error CARD-MEMORY Copy Copying MEMORY-CARDCOPY Program Y/N Initializing Advanced Mode Service Mode GAP Input Service ModeGAP Input EYE Input Auto Online Feed YES no Feed on Error EXT PIN 9 Select MODE1 MODE2 Euro Code Reprint W/FEED YES noLabel RE-DETECT Enable Disable Counters HD CUT Life Head Counter Head Count Clear YES no Counters ModeTest Print Mode Advanced Mode Counters ModeTest Print Size Default Setting ModeTest Print Mode Configuration Initializing Default Setting YES noInitializing User Download Press the Line KEY Default Setting CompletedClear NON-STANDARD Protocol Download User Defined Protocol CodesHEX Dump Mode User Download WaitingInitializing Online Print Darkness Adjusting the Print QualityPrint Speed Cleaning the Print HEAD, Platen and RollersCleaning the Platen and Rollers Cleaning the Label Edge SensorsSupplies needed Flat blade screwdriver Replacing the Print HeadDo not remove the two outside Screws painted red on either This page left intentionally blank Using the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceUsing the LAN Ethernet Interface Using the Universal Serial BUS USB InterfaceChecking the Network Connection and Cabling Troubleshooting LED LCD Message Audible Error Possible Causes Beep Condition Error SignalsInterface Types Section Interface SpecificationsReceive Buffer Single JOB BufferMulti JOB Buffer IEEE1284 Parallel Interface Data Streams Electrical SpecificationsRS232 Serial Interface General SpecificationsPIN Assignments ON/X-OFF Flow Control Cable Requirements READY/BUSY Flow ControlUniversal Serial BUS USB Interface Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications Print JOB Cancel canENQUIRE/ACK/NAK Enquire ENQPrint Start DC1 Print Stop DLEInstallation Error HandlingPcmcia Memory Cards Description PLUG-IN Interface Modules Error Description Indication RemedyOperator Setup CutterGeneral Operation Label Dispense Option Removing and Unwinding the Roll Label RewinderReal Time Clock

M-84PRO specifications

The SATO M-84PRO is a high-performance thermal printer designed for industrial applications, known for its reliability and efficiency in various labeling tasks. This printer is a part of SATO's esteemed M-84 series, which combines advanced technology with user-friendly design to meet the demands of large-scale operations.

One of the standout features of the SATO M-84PRO is its fast printing speed, capable of producing labels at a rate of up to 8 inches per second. This rapid output makes it an ideal choice for environments that require quick turnaround times, such as warehouses, manufacturing lines, and logistics centers.

The M-84PRO employs a direct thermal or thermal transfer printing method, allowing for outstanding print quality. With a maximum print resolution of 305 dpi, it ensures crisp and clear text and graphics, which is essential for barcodes and detailed images on labels. The printer supports a wide range of media types, accommodating label widths from 0.75 inches to 4.1 inches, making it versatile for various labeling needs.

Equipped with SATO's unique Smart Technology, the M-84PRO offers enhanced control over label production. This technology includes automatic label detection and calibration, which minimizes setup time and reduces waste, thus improving overall operational efficiency. Additionally, the printer is compatible with various programming languages, including SAPscript and ZPL, ensuring easy integration into existing systems.

Durability is another hallmark of the M-84PRO. Built with robust materials, it can withstand the rigors of industrial environments, ensuring long-term performance. The printer also features a compact design, which is perfect for tight workspaces, while still being rugged enough to handle demanding tasks.

Moreover, the SATO M-84PRO boasts extensive connectivity options, including USB, Ethernet, and serial interfaces, which allow for seamless integration into any operational workflow. It also supports various operating systems, providing flexibility and ease of use when working with different platforms.

The printer’s user-friendly interface, highlighted by an LCD panel and multi-functional buttons, facilitates easy navigation and operation. Maintenance is also simplified, thanks to modular components that allow for quick and easy replacement of parts when necessary.

In summary, the SATO M-84PRO stands out as a leading choice in the thermal printer market, combining high-speed printing, excellent durability, and versatile labeling capabilities. Its advanced technologies and features make it suitable for a variety of demanding applications, ensuring that businesses can rely on it for their labeling needs.
Top Page Image Contents