SATO M-84PRO manual Cutter, Operator Setup, General Operation

Page 79

Section 7. Optional Accessories

CUTTER

The label cutter consists of an internal mechanism that will cut labels or tags as they exit from the printer. The cutter can be used to print labels of various lengths using continuous form label/tag stock or to easily separate labels when there is no perforation at the label gap.

OPERATOR SETUP

The following steps should be taken to set up the label cutter.

1.Install the label cutter, following the instructions provided with the unit.

2.Power the printer ON.

3.The printer must be configured to use the Label Cutter option. Switches DSW3-1 and DSW3-2 on the front panel are used to configure the printer. To enable the cutter, DSW3-1 should be in the ON position and DSW3-2 should bein the OFF position.

4.Open the Print Head Assembly and feed the edge of the labels/tags into the cutter assembly and out between the label cutters.

NOTE: Although the cutting blade is fairly well protected, be careful as you feed labels into the cutter area. You may want to have the printer powered OFF at this point.

5.Close the Print Head Assembly and place the printer on-line.

6.The Label Cutter is ready for use.

7.Adjust the cut position using the backfeed adjustment procedures outlined in Section 2. Installation.

GENERAL OPERATION

The data stream to be sent to the printer may need to be altered to add the Cutter Command. If this command is not used, the cutter will default to cut after every label assuming it has been enabled in the printer configuration. For more details, see the “e” and PRO Printer Programming Reference. As the labels are printed, they will be cut based on the the data supplied using the cutter command.

SATO M-84PRO

PN 9001105 Rev. A

Page 7-3

Page 78 Page 80
Image 79
Page 78 Page 80
Contents 84PRO Page Table of Contents Interface Specifications Introduction Section Printer OverviewSpecification General Printer Specifications84PRO All Models Matrix Fonts Character FontsBAR Code BAR CodesPhysical PowerAccessories and Options Optional AccessoriesThis page left intentionally blank Section Installation Unpacking and Parts Identification Setting UP the Printer LCD Loading Labels and Tags Installation Route Labels Under Guide Head Latch Loading the Ribbon Tape Operator Panel DSW On LineLine FeedRear Panel Head Open Sensor SensorsLabel Indexing Sensor This page left intentionally blank OFF Printer DIP Switch ConfigurationDIP Switch Panels RS232 TRANSMIT/RECEIVE SettingDSW2 OFF Printer SET UPHex Dump Selection DSW2-4.Selects Hex Dump mode see DSW3 DSW3 OFF SettingDSW3-6 DSW3-7 Default Completed Default SettingsSwitch Selections Software Default SettingsPitch Potentiometer AdjustmentsBackfeed Offset Print DisplayInitializing Online QTY000000 LCD Panel Printer ConfigurationNormal Mode Mode KEY Sequence Initial DisplayPrint Speed Print DarknessPitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Initializing Advanced ModeSET Calendar YES no Print OffsetIgnore CR/LF YES no CalendarCharacter Pitch Prop Fixed Advanced Mode Card ModeCopy Start YES no Truetype Fontcopy Completed Card COPY/FORMAT Xxxxxxx Error CARD-MEMORY Copy Copying MEMORY-CARDCOPY Program Y/N Initializing Advanced Mode Service Mode GAP Input Service ModeGAP Input EYE Input Auto Online Feed YES no Feed on Error EXT PIN 9 Select MODE1 MODE2 Euro Code Reprint W/FEED YES noLabel RE-DETECT Enable Disable Counters HD CUT Life Head Counter Head Count Clear YES no Counters ModeTest Print Mode Advanced Mode Counters ModeTest Print Size Default Setting ModeTest Print Mode Configuration Initializing Default Setting YES noInitializing User Download Press the Line KEY Default Setting CompletedClear NON-STANDARD Protocol Download User Defined Protocol CodesUser Download Waiting HEX Dump ModeInitializing Online Print Darkness Adjusting the Print QualityPrint Speed Cleaning the Print HEAD, Platen and RollersCleaning the Platen and Rollers Cleaning the Label Edge SensorsSupplies needed Flat blade screwdriver Replacing the Print HeadDo not remove the two outside Screws painted red on either This page left intentionally blank Using the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceUsing the LAN Ethernet Interface Using the Universal Serial BUS USB InterfaceChecking the Network Connection and Cabling Troubleshooting LED LCD Message Audible Error Possible Causes Beep Condition Error SignalsInterface Types Section Interface SpecificationsSingle JOB Buffer Receive BufferMulti JOB Buffer IEEE1284 Parallel Interface Data Streams Electrical SpecificationsRS232 Serial Interface General SpecificationsPIN Assignments ON/X-OFF Flow Control Cable Requirements READY/BUSY Flow ControlLocal Area Network LAN Optional Interface Universal Serial BUS USB InterfaceBI-DIRECTIONAL Communications Print JOB Cancel canENQUIRE/ACK/NAK Enquire ENQPrint Start DC1 Print Stop DLEError Handling InstallationPcmcia Memory Cards Description PLUG-IN Interface Modules Error Description Indication RemedyCutter Operator SetupGeneral Operation Label Dispense Option Removing and Unwinding the Roll Label RewinderReal Time Clock

M-84PRO specifications

The SATO M-84PRO is a high-performance thermal printer designed for industrial applications, known for its reliability and efficiency in various labeling tasks. This printer is a part of SATO's esteemed M-84 series, which combines advanced technology with user-friendly design to meet the demands of large-scale operations.

One of the standout features of the SATO M-84PRO is its fast printing speed, capable of producing labels at a rate of up to 8 inches per second. This rapid output makes it an ideal choice for environments that require quick turnaround times, such as warehouses, manufacturing lines, and logistics centers.

The M-84PRO employs a direct thermal or thermal transfer printing method, allowing for outstanding print quality. With a maximum print resolution of 305 dpi, it ensures crisp and clear text and graphics, which is essential for barcodes and detailed images on labels. The printer supports a wide range of media types, accommodating label widths from 0.75 inches to 4.1 inches, making it versatile for various labeling needs.

Equipped with SATO's unique Smart Technology, the M-84PRO offers enhanced control over label production. This technology includes automatic label detection and calibration, which minimizes setup time and reduces waste, thus improving overall operational efficiency. Additionally, the printer is compatible with various programming languages, including SAPscript and ZPL, ensuring easy integration into existing systems.

Durability is another hallmark of the M-84PRO. Built with robust materials, it can withstand the rigors of industrial environments, ensuring long-term performance. The printer also features a compact design, which is perfect for tight workspaces, while still being rugged enough to handle demanding tasks.

Moreover, the SATO M-84PRO boasts extensive connectivity options, including USB, Ethernet, and serial interfaces, which allow for seamless integration into any operational workflow. It also supports various operating systems, providing flexibility and ease of use when working with different platforms.

The printer’s user-friendly interface, highlighted by an LCD panel and multi-functional buttons, facilitates easy navigation and operation. Maintenance is also simplified, thanks to modular components that allow for quick and easy replacement of parts when necessary.

In summary, the SATO M-84PRO stands out as a leading choice in the thermal printer market, combining high-speed printing, excellent durability, and versatile labeling capabilities. Its advanced technologies and features make it suitable for a variety of demanding applications, ensuring that businesses can rely on it for their labeling needs.
Top Page Image Contents