SATO M-84PRO manual EYE Input Auto Online Feed YES no Feed on Error

Page 48

Section 3. Configuration

EYE [X.XXV]

INPUT [X.XV]

AUTO ONLINE FEED

YES NO

FEED ON ERROR

YES NO

EYE - When setting the “eye” threshold, the voltage must be measured with nothing but the label under the sensor and then again withthe printed “eye” mark under the sensor. The formula for this is:

(High Voltage Level + Low Voltage Level) x 0.5 = Start Value

1.Insert a label into the sensor and close the Label Hold- Down. Make sure the printed “eye” mark is not under the sensor. Record the voltage shown on the top line of the LCD panel. This line should have the message “EYE” on the top line (DIP switch DSW2-2 = ON).

2.Now pull the label forward until the “eye” mark is positioned under the sensor (the voltage reading should be at its highest point). Record the voltage shown on the top line of the LCD panel. The voltage ranges measured should be within the following ranges:

Eye-Mark = 2.5V to 3.5V Label Only = Less than 1.0V

If the measured values are outside this range, you may have trouble in finding a value that will work properly under all conditions. If this is the case, a higher quality label may be needed to get adequate performance.

3.Calculate the starting point voltage using the formula.

4.Use the LINE and FEED keys to step the counter to the desired setting. The reading will advance to a setting of 4.9 (the maximum voltage). If a value of “0.0” is set, the printer will automatically set the level each time the printer is powered on with labels loaded or the head is closed.

5.Once the setting is correct, pressing the ENTER key will accept the setting and advance to the next display.

This selection specifies whether or not the printer will feed a label when it is placed in the Online mode.

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will feed a blank label anytime it enters the Online mode.

2.Once the setting is correct, pressing the FEED key will accept the setting and advance to the next display.

This selection specifies whether or not the printer will feed a label when an error condition is cleared..

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will feed a blank label anytime an error condition is cleared.

2.Once the setting is correct, pressing the FEED key will accept the setting and advance to the next display.

Page 3-22

PN 9001105 Rev. A

SATO M-84PRO

Page 47 Page 49
Image 48
Page 47 Page 49
Contents 84PRO Page Table of Contents Interface Specifications Section Printer Overview IntroductionGeneral Printer Specifications Specification84PRO All Models Character Fonts Matrix FontsBAR Codes BAR CodePower PhysicalOptional Accessories Accessories and OptionsThis page left intentionally blank Section Installation Unpacking and Parts Identification Setting UP the Printer LCD Loading Labels and Tags Installation Route Labels Under Guide Head Latch Loading the Ribbon Tape Operator Panel On Line LineFeed DSWRear Panel Sensors Head Open SensorLabel Indexing Sensor This page left intentionally blank Printer DIP Switch Configuration DIP Switch PanelsRS232 TRANSMIT/RECEIVE Setting OFFPrinter SET UP DSW2 OFFHex Dump Selection DSW2-4.Selects Hex Dump mode see DSW3 Setting DSW3 OFFDSW3-6 DSW3-7 Default Settings Switch SelectionsSoftware Default Settings Default CompletedPotentiometer Adjustments PitchBackfeed Offset Display PrintLCD Panel Printer Configuration Normal ModeMode KEY Sequence Initial Display Initializing Online QTY000000Print Darkness Print SpeedPitch Offset + 00mm Advanced Mode Cancel Print JOB YES no CompletedInitializing Advanced Mode Zero Slash YES no Auto OnlinePrint Offset SET Calendar YES noCalendar Ignore CR/LF YES noCard Mode Character Pitch Prop Fixed Advanced ModeCopy Start YES no Truetype Fontcopy Completed Card COPY/FORMAT Xxxxxxx Error CARD-MEMORY Copy Copying MEMORY-CARDCOPY Program Y/N Service Mode Initializing Advanced Mode Service Mode GAP InputGAP Input EYE Input Auto Online Feed YES no Feed on Error Reprint W/FEED YES no EXT PIN 9 Select MODE1 MODE2 Euro CodeLabel RE-DETECT Enable Disable Counters Mode Test Print ModeAdvanced Mode Counters Mode Counters HD CUT Life Head Counter Head Count Clear YES noDefault Setting Mode Test Print Mode ConfigurationInitializing Default Setting YES no Test Print SizeDefault Setting Completed Clear NON-STANDARD ProtocolDownload User Defined Protocol Codes Initializing User Download Press the Line KEYHEX Dump Mode User Download WaitingInitializing Online Adjusting the Print Quality Print DarknessCleaning the Print HEAD, Platen and Rollers Print SpeedCleaning the Label Edge Sensors Cleaning the Platen and RollersReplacing the Print Head Supplies needed Flat blade screwdriverDo not remove the two outside Screws painted red on either This page left intentionally blank Initial Checklist Using the IEEE1284 Parallel InterfaceUsing the RS232C Serial Interface TroubleshootingUsing the Universal Serial BUS USB Interface Using the LAN Ethernet InterfaceChecking the Network Connection and Cabling Troubleshooting Error Signals LED LCD Message Audible Error Possible Causes Beep ConditionSection Interface Specifications Interface TypesReceive Buffer Single JOB BufferMulti JOB Buffer IEEE1284 Parallel Interface Electrical Specifications Data StreamsGeneral Specifications RS232 Serial InterfacePIN Assignments Cable Requirements READY/BUSY Flow Control ON/X-OFF Flow ControlUniversal Serial BUS USB Interface Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications Cancel can ENQUIRE/ACK/NAKEnquire ENQ Print JOBPrint Stop DLE Print Start DC1Installation Error HandlingPcmcia Memory Cards Description Error Description Indication Remedy PLUG-IN Interface ModulesOperator Setup CutterGeneral Operation Label Dispense Option Label Rewinder Removing and Unwinding the RollReal Time Clock

M-84PRO specifications

The SATO M-84PRO is a high-performance thermal printer designed for industrial applications, known for its reliability and efficiency in various labeling tasks. This printer is a part of SATO's esteemed M-84 series, which combines advanced technology with user-friendly design to meet the demands of large-scale operations.

One of the standout features of the SATO M-84PRO is its fast printing speed, capable of producing labels at a rate of up to 8 inches per second. This rapid output makes it an ideal choice for environments that require quick turnaround times, such as warehouses, manufacturing lines, and logistics centers.

The M-84PRO employs a direct thermal or thermal transfer printing method, allowing for outstanding print quality. With a maximum print resolution of 305 dpi, it ensures crisp and clear text and graphics, which is essential for barcodes and detailed images on labels. The printer supports a wide range of media types, accommodating label widths from 0.75 inches to 4.1 inches, making it versatile for various labeling needs.

Equipped with SATO's unique Smart Technology, the M-84PRO offers enhanced control over label production. This technology includes automatic label detection and calibration, which minimizes setup time and reduces waste, thus improving overall operational efficiency. Additionally, the printer is compatible with various programming languages, including SAPscript and ZPL, ensuring easy integration into existing systems.

Durability is another hallmark of the M-84PRO. Built with robust materials, it can withstand the rigors of industrial environments, ensuring long-term performance. The printer also features a compact design, which is perfect for tight workspaces, while still being rugged enough to handle demanding tasks.

Moreover, the SATO M-84PRO boasts extensive connectivity options, including USB, Ethernet, and serial interfaces, which allow for seamless integration into any operational workflow. It also supports various operating systems, providing flexibility and ease of use when working with different platforms.

The printer’s user-friendly interface, highlighted by an LCD panel and multi-functional buttons, facilitates easy navigation and operation. Maintenance is also simplified, thanks to modular components that allow for quick and easy replacement of parts when necessary.

In summary, the SATO M-84PRO stands out as a leading choice in the thermal printer market, combining high-speed printing, excellent durability, and versatile labeling capabilities. Its advanced technologies and features make it suitable for a variety of demanding applications, ensuring that businesses can rely on it for their labeling needs.
Top Page Image Contents