Star Micronics TSP1000 Connecting Ethernet Cable, Ethernet cable, Ferrite core, 10cm, Fastener

Page 13

4-1-4. Connecting Ethernet Cable

4-1-4. Connecting Ethernet Cable

(1) Make sure the printer is turned off.

	(2) Affix the ferrite core onto the
	ethernet cable as shown in the illus-	Ethernet cable
	tration below.	Ethernet cable
	tration below.
		Ferrite core

(3) Pass the fastener through the ferrite	10cm
core.	(Maximum)
core.

Fastener

(4) Loop the fastener around the cable and lock it. Use scissors to cut off any excess.

(5)Connect the ethernet cable to the connector on the interface board.

Then, connect the other end of the cable to your computer.

– 9 –

Image 13

Contents THERMAL PRINTER TSP1000 SERIESUSER’S MANUAL Page Statement Federal Communications Commission Radio Frequency InterferenceStatement of The Canadian Department of Communications Radio Interference RegulationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer Core outer 3. Consumable Parts and AC AdapterCore inner Page 4-1. Interface Cable 4. Connecting Cables and AC Adapter4-1-1. Serial Interface RS-232C Cable Ferrite core Interface cable 4-1-2. Parallel Interface Cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB CableEthernet cable 4-1-4. Connecting Ethernet CableFerrite core 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation 5. Control Panel and Other Functions Errors5-1. Control Panel 1 If a non recoverable error occurs, turn the power OFF immediately 3 Non recoverable error4 Paper detection error 5-3. Self Printing Be sure to use roll paper that matches the printer’s specification 6. Loading the Roll Paper1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-1. Preventing Paper Jams 8. Preventing and Clearing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9-1. Cleaning the Thermal Head 9. Periodical Cleaning9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A SpecificationsA-4. Electrical Characteristics A-2. Auto Cutter SpecificationsA-3. Interface A-5. OptionA-7. Reliability A-6. Environmental Requirements20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µmRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting No. 1 2 3 4 5 6 7 DIP-SW1 B-1. Parallel Interface ModelNo. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelB-4. Ethernet Interface Model Green Lights when other party connection is recognized as 10BASE-T Installing the Printer Driver and the LPR Port Driver SetOrange Lights when packets are received LED DisplayAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorD-sub 9 Pin D-sub 25 PinPrinter status DIP SWD-2. Cable Connections D-3. Electrical CharacteristicsHost side D-sub 25 pinE-2. Ethernet Interface Specifications E-1. USB Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC