Star Micronics TSP1000 user manual Appendix A Specifications, A-1. General Specifications

Page 31

Appendix A: Specifications

	Appendix A: Specifications
A-1. General Specifications
(1)Printing method	Direct line thermal printing
(2)Print speed	Max. 1440 dots/sec. (180 mm/sec.)
(3)Dot density	203 dpi: 8 dots/mm (0.125 mm/dot)
(4)Printing width	Max. 80 mm
(5)Number of print columns
	53 (12 ⋅ 24 dots)
(6)Roll paper	Refer to chapter 3 for details on the recommended roll
	paper.
	Paper width: 82.5 ± 0.5 mm
	Roll diameter: ø180 mm or less
(7)Overall dimension	161 (W) ⋅ 307 (D) ⋅ 249 (H) mm
(8)Weight	Approx. 3.0 kg
(9)Noise Approx.	57 dB

161

249

307

Unit : mm

– 27 –

Image 31

Contents THERMAL PRINTER TSP1000 SERIESUSER’S MANUAL Page Radio Interference Regulations Federal Communications Commission Radio Frequency InterferenceStatement Statement of The Canadian Department of CommunicationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer Core outer 3. Consumable Parts and AC AdapterCore inner Page 4-1. Interface Cable 4. Connecting Cables and AC Adapter4-1-1. Serial Interface RS-232C Cable Ferrite core Interface cable 4-1-2. Parallel Interface Cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB Cable10cm 4-1-4. Connecting Ethernet CableEthernet cable Ferrite core4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation 5. Control Panel and Other Functions Errors5-1. Control Panel 1 If a non recoverable error occurs, turn the power OFF immediately 3 Non recoverable error4 Paper detection error 5-3. Self Printing Be sure to use roll paper that matches the printer’s specification 6. Loading the Roll Paper1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-1. Preventing Paper Jams 8. Preventing and Clearing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9-1. Cleaning the Thermal Head 9. Periodical Cleaning9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A SpecificationsA-5. Option A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-3. Interface1.0 million cuttings if the paper thickness is 100 µm A-6. Environmental RequirementsA-7. Reliability 20 million lines based on an average printing rate ofRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting No. 1 2 3 4 5 6 7 DIP-SW1 B-1. Parallel Interface ModelNo. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelB-4. Ethernet Interface Model LED Display Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T Orange Lights when packets are receivedAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorDIP SW D-sub 25 PinD-sub 9 Pin Printer statusD-sub 25 pin D-3. Electrical CharacteristicsD-2. Cable Connections Host sideE-2. Ethernet Interface Specifications E-1. USB Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC