Star Micronics TSP1000 user manual A-2. Auto Cutter Specifications, A-3. Interface, A-5. Option

Page 32
A-2. Auto Cutter Specifications

A-2. Auto Cutter Specifications

(1) Cutting frequency

Max. 20 cuts per minute

(2) Thickness of paper

0.080 ~ 0.105 mm

A-3. Interface

RS232C serial interface/Two-way parallel interface (IEEE1284)/USB interface/ Ethernet interface

A-4. Electrical Characteristics

(1) Input Voltage

DC 24V±10%

 

(2) Current Consumption

Operating: Approx. 2.0 A (at ASCII printing)

 

 

 

Peak:

Approx. 10 A (at print duty 100%,

 

 

 

 

for 10 seconds or less)

 

 

 

Stand-by:

Approx. 0.1 A

 

(3) Power Connector

 

 

 

 

 

 

 

 

 

 

Pin No.

Function

 

1

3

 

 

 

 

 

1

Drive power

 

 

 

 

 

 

 

 

 

 

2

Signal GND

 

 

2

 

3

N.C.

 

 

 

 

Shell

Frame ground

 

<Viewed from Connector Surface>

 

 

 

 

 

 

 

 

Important!

When using a printer power supply other than the optional AC adaptor (PS60L-24A), be sure that the following cautions are observed.

Use a power supply of DC 24 V ±10% and more than 2.0 A (5.0 A Load 10 sec. Min) with SELV output approved by IEC60950.

Be careful about installing the printer in an area where there is noise. Take the appropriate measures to protect against electrostatic AC line noise, etc.

A-5. Option

(1)USB Interface Board Unit (IFBD-HU04)

(2)Parallel Interface Board Unit (IFBD-HC04)

(3)25 Pin RS-232C Interface Board Unit (IFBD-HD04)

(4)9 Pin RS-232C Interface Board Unit (IFBD-HN04)

(5)Ethernet Interface Board Unit (IFBD-HE04)

– 28 –

Image 32
Contents USER’S MANUAL TSP1000 SERIESTHERMAL PRINTER Page Federal Communications Commission Radio Frequency Interference StatementStatement of The Canadian Department of Communications Radio Interference RegulationsTABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking2. Parts Identification and Nomenclature Choosing a place for the printer Core inner 3. Consumable Parts and AC AdapterCore outer Page 4-1-1. Serial Interface RS-232C Cable 4. Connecting Cables and AC Adapter4-1. Interface Cable 5 cm maximum Fastener Pull and cut 4-1-2. Parallel Interface CableFerrite core Interface cable 4-1-3. Connecting USB Cable Parallel interface cable4-1-4. Connecting Ethernet Cable Ethernet cableFerrite core 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in4-5. Installing the Cable Install the cable as shown in the diagram below4-6. Switch Blind Installation 5-1. Control Panel Errors5. Control Panel and Other Functions 4 Paper detection error 3 Non recoverable error1 If a non recoverable error occurs, turn the power OFF immediately 5-3. Self Printing 1 Push the Cover open lever, and open the printer cover 6. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-2. Removing Paper Jam 8. Preventing and Clearing Paper Jams8-1. Preventing Paper Jams 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade9-2. Cleaning the Paper Holder 9. Periodical Cleaning9-1. Cleaning the Thermal Head Appendix A Specifications A-1. General SpecificationsA-2. Auto Cutter Specifications A-4. Electrical CharacteristicsA-3. Interface A-5. OptionA-6. Environmental Requirements A-7. Reliability20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µmA-8. Black Mark Specifications RemarksAppendix B Dip Switch Setting No. 1 2 3 DIP-SW2 B-1. Parallel Interface ModelNo. 1 2 3 4 5 6 7 DIP-SW1 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3B-3. USB Interface Model Printer Driver URLB-4. Ethernet Interface Model Installing the Printer Driver and the LPR Port Driver Set Green Lights when other party connection is recognized as 10BASE-TOrange Lights when packets are received LED DisplayTable of Connection Signals for Each Mode Appendix C Parallel InterfaceD-1. RS-232C Connector Appendix D Serial Interface RS-232CD-sub 25 Pin D-sub 9 PinPrinter status DIP SWD-3. Electrical Characteristics D-2. Cable ConnectionsHost side D-sub 25 pinAppendix E USB Interface and Ethernet Interface E-1. USB Interface SpecificationsE-2. Ethernet Interface Specifications Appendix F Buzzer Driver Circuit Modular plugDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC