Star Micronics TSP1000 user manual Connecting the Optional AC Adapter

Page 15
4-3. Connecting the Optional AC Adapter

4-3. Connecting the Optional AC Adapter

Note: Before connecting/disconnecting the AC adapter, make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet.

(1)Connect the AC adapter to the power cable.

Note: Use only the standard AC adapter and power cable.

(2)Connect AC adapter to the connector on the printer.

(3)Insert the power cable plug into an AC outlet.

Important!

When disconnecting the cable, take hold of the cable connector to pull it out. Releasing the lock makes it easy to disconnect the connector.

Pulling the cable excessively could cause damage to the connector.

– 11 –

Image 15
Contents TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Radio Interference Regulations Federal Communications Commission Radio Frequency InterferenceStatement Statement of The Canadian Department of CommunicationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB Cable10cm 4-1-4. Connecting Ethernet CableEthernet cable Ferrite core4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A SpecificationsA-5. Option A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-3. Interface1.0 million cuttings if the paper thickness is 100 µm A-6. Environmental RequirementsA-7. Reliability 20 million lines based on an average printing rate ofRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelB-4. Ethernet Interface Model LED Display Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T Orange Lights when packets are receivedAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorDIP SW D-sub 25 PinD-sub 9 Pin Printer statusD-sub 25 pin D-3. Electrical CharacteristicsD-2. Cable Connections Host sideE-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC