Star Micronics TSP1000 user manual Self Printing

Page 21

5-3. Self Printing

5-3. Self Printing

(1)Test Printing

Turn the power on while holding the FEED button depressed.

Test printing will be performed according to the Ver. No., DIP switch settings and memory switch settings.

(2) Hexadecimal Dump Mode

Open the printer cover, then turn the power on while holding the FEED button. When the cover is closed, “*** HEX DUMP PRINTING ***” is printed, and the printer enters the Hexadecimal Dump Mode.

Each of the signals sent from the computer to the printer will be printed out in hexadecimal code.

This function allows you to check if a control code sent to the printer by the program being used is correct or not. The final line is not printed if its data is less than one full line. However, if the FEED button is pushed, the final line is printed. To turn off the mode, it is necessary to turn off the printer completely.

– 17 –

Image 21

Contents TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Statement Federal Communications Commission Radio Frequency InterferenceStatement of The Canadian Department of Communications Radio Interference RegulationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB CableEthernet cable 4-1-4. Connecting Ethernet CableFerrite core 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A SpecificationsA-4. Electrical Characteristics A-2. Auto Cutter SpecificationsA-3. Interface A-5. OptionA-7. Reliability A-6. Environmental Requirements20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µmRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelB-4. Ethernet Interface Model Green Lights when other party connection is recognized as 10BASE-T Installing the Printer Driver and the LPR Port Driver SetOrange Lights when packets are received LED DisplayAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorD-sub 9 Pin D-sub 25 PinPrinter status DIP SWD-2. Cable Connections D-3. Electrical CharacteristicsHost side D-sub 25 pinE-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC