Star Micronics TSP1000 user manual B-1. Parallel Interface Model, No. 1 2 3 4 5 6 7 DIP-SW1

Page 36

B-1. Parallel Interface Model

ON

OFF

No. 1 2 3 4 5 6 7 8

DIP-SW1

ON

OFF

No. 1 2 3 4

DIP-SW2

DIP-SW 1

Switch	Function		ON	OFF

1-1	Command emulation		See table below

1-2	Command emulation
1-2	Command emulation

1-3	Should not be changed (Should be set to on)

1-4	Sensor adjustment		Valid	Invalid

1-5	Pin #31 (INIT) reset signal		Valid	Invalid

1-6	Handshaking conditions		Offline or receive	Receive buffer full
	(conditions for BUSY)		buffer full

1-7	Automatic status back function		Invalid	Valid

1-8	Should not be changed (Should be set to on)

The factory settings of DIP switch are all on.

Switch 1-1	Switch 1-2	Command emulation

ON	ON	Star Line Mode

OFF	ON	Star Page Mode

OFF	OFF	ESC/POS Mode

DIP-SW 2

Switch	Function	ON		OFF

2-1

2-2	Always ON		Should be set to on

2-3
2-3

2-4

The factory settings of DIP switch are all on.

– 32 –

Image 36

Contents TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Federal Communications Commission Radio Frequency Interference StatementStatement of The Canadian Department of Communications Radio Interference RegulationsTABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut 4-1-3. Connecting USB Cable Parallel interface cable4-1-4. Connecting Ethernet Cable Ethernet cableFerrite core 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in4-5. Installing the Cable Install the cable as shown in the diagram below4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder Appendix A Specifications A-1. General SpecificationsA-2. Auto Cutter Specifications A-4. Electrical CharacteristicsA-3. Interface A-5. OptionA-6. Environmental Requirements A-7. Reliability20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µmA-8. Black Mark Specifications RemarksAppendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3B-3. USB Interface Model Printer Driver URLB-4. Ethernet Interface Model Installing the Printer Driver and the LPR Port Driver Set Green Lights when other party connection is recognized as 10BASE-TOrange Lights when packets are received LED DisplayTable of Connection Signals for Each Mode Appendix C Parallel InterfaceD-1. RS-232C Connector Appendix D Serial Interface RS-232CD-sub 25 Pin D-sub 9 PinPrinter status DIP SWD-3. Electrical Characteristics D-2. Cable ConnectionsHost side D-sub 25 pinE-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Appendix F Buzzer Driver Circuit Modular plugDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC