Star Micronics TSP1000 user manual Connecting USB Cable, Parallel interface cable

Page 12

Parallel interface cable

(5)Connect the interface cable to the connector on the rear panel of the printer.

(6)Fasten the connector clasps.

Parallel interface cable

4-1-3. Connecting USB Cable

(1)Make sure the printer is turn off.

(2)Affix the ferrite core onto the USB cable as shown in the illustration below and make sure to pass the cable through the cable support as shown in the illustration.

– 8 –

Image 12

Contents TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Federal Communications Commission Radio Frequency Interference StatementStatement of The Canadian Department of Communications Radio Interference RegulationsTABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut 4-1-3. Connecting USB Cable Parallel interface cable4-1-4. Connecting Ethernet Cable Ethernet cableFerrite core 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in4-5. Installing the Cable Install the cable as shown in the diagram below4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder Appendix A Specifications A-1. General SpecificationsA-2. Auto Cutter Specifications A-4. Electrical CharacteristicsA-3. Interface A-5. OptionA-6. Environmental Requirements A-7. Reliability20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µmA-8. Black Mark Specifications RemarksAppendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3B-3. USB Interface Model Printer Driver URLB-4. Ethernet Interface Model Installing the Printer Driver and the LPR Port Driver Set Green Lights when other party connection is recognized as 10BASE-TOrange Lights when packets are received LED DisplayTable of Connection Signals for Each Mode Appendix C Parallel InterfaceD-1. RS-232C Connector Appendix D Serial Interface RS-232CD-sub 25 Pin D-sub 9 PinPrinter status DIP SWD-3. Electrical Characteristics D-2. Cable ConnectionsHost side D-sub 25 pinE-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Appendix F Buzzer Driver Circuit Modular plugDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC