Star Micronics TSP1000 user manual Loading the Roll Paper

Page 22

6. Loading the Roll Paper

6. Loading the Roll Paper

Be sure to use roll paper that matches the printer’s specification.

(1) Push the Cover open lever, and open the printer cover.

Cover open lever

Roll paper

(2) While observing the direction of the roll, set the paper roll into the hol- low, and pull on the leading edge of the paper toward you.

– 18 –

Image 22

Contents THERMAL PRINTER TSP1000 SERIESUSER’S MANUAL Page Statement of The Canadian Department of Communications Federal Communications Commission Radio Frequency InterferenceStatement Radio Interference RegulationsTABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking2. Parts Identification and Nomenclature Choosing a place for the printer Core outer 3. Consumable Parts and AC AdapterCore inner Page 4-1. Interface Cable 4. Connecting Cables and AC Adapter4-1-1. Serial Interface RS-232C Cable Ferrite core Interface cable 4-1-2. Parallel Interface Cable5 cm maximum Fastener Pull and cut 4-1-3. Connecting USB Cable Parallel interface cableFerrite core 4-1-4. Connecting Ethernet CableEthernet cable 10cm4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in4-5. Installing the Cable Install the cable as shown in the diagram below4-6. Switch Blind Installation 5. Control Panel and Other Functions Errors5-1. Control Panel 1 If a non recoverable error occurs, turn the power OFF immediately 3 Non recoverable error4 Paper detection error 5-3. Self Printing Be sure to use roll paper that matches the printer’s specification 6. Loading the Roll Paper1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-1. Preventing Paper Jams 8. Preventing and Clearing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade9-1. Cleaning the Thermal Head 9. Periodical Cleaning9-2. Cleaning the Paper Holder Appendix A Specifications A-1. General SpecificationsA-3. Interface A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-5. Option20 million lines based on an average printing rate of A-6. Environmental RequirementsA-7. Reliability 1.0 million cuttings if the paper thickness is 100 µmA-8. Black Mark Specifications RemarksAppendix B Dip Switch Setting No. 1 2 3 4 5 6 7 DIP-SW1 B-1. Parallel Interface ModelNo. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3B-3. USB Interface Model Printer Driver URLB-4. Ethernet Interface Model Orange Lights when packets are received Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T LED DisplayTable of Connection Signals for Each Mode Appendix C Parallel InterfaceD-1. RS-232C Connector Appendix D Serial Interface RS-232CPrinter status D-sub 25 PinD-sub 9 Pin DIP SWHost side D-3. Electrical CharacteristicsD-2. Cable Connections D-sub 25 pinE-2. Ethernet Interface Specifications E-1. USB Interface SpecificationsAppendix E USB Interface and Ethernet Interface Appendix F Buzzer Driver Circuit Modular plugDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC