Star Micronics
TSP1000
user manual
Specification
Install
Errors
Connecting USB Cable
D-1. RS-232C Connector
Periodical Cleaning
Non recoverable error
Turning Power On
Switch Blind Installation
Page 51
Page 50
Page 52
Image 51
Page 50
Page 52
Contents
TSP1000 SERIES
THERMAL PRINTER
USER’S MANUAL
Page
Radio Interference Regulations
Federal Communications Commission Radio Frequency Interference
Statement
Statement of The Canadian Department of Communications
TABLE OF CONTENTS
1-1. Unpacking
1. Unpacking and Installation
2. Parts Identification and Nomenclature
Choosing a place for the printer
3. Consumable Parts and AC Adapter
Core outer
Core inner
Page
4. Connecting Cables and AC Adapter
4-1. Interface Cable
4-1-1. Serial Interface RS-232C Cable
4-1-2. Parallel Interface Cable
Ferrite core Interface cable
5 cm maximum Fastener Pull and cut
Parallel interface cable
4-1-3. Connecting USB Cable
10cm
4-1-4. Connecting Ethernet Cable
Ethernet cable
Ferrite core
4-2. Connecting to a Buzzer Drive
4-3. Connecting the Optional AC Adapter
Make sure that the AC adapter has been connected as described in
4-4. Turning Power On
Install the cable as shown in the diagram below
4-5. Installing the Cable
4-6. Switch Blind Installation
Errors
5. Control Panel and Other Functions
5-1. Control Panel
3 Non recoverable error
1 If a non recoverable error occurs, turn the power OFF immediately
4 Paper detection error
5-3. Self Printing
6. Loading the Roll Paper
Be sure to use roll paper that matches the printer’s specification
1 Push the Cover open lever, and open the printer cover
Note Make sure that the printer cover is securely closed
1. Do not touch the cutter blade
7. Adjusting the Near-end Sensor
Adjustment value according to the paper you are using
8. Preventing and Clearing Paper Jams
8-1. Preventing Paper Jams
8-2. Removing Paper Jam
8-3. Releasing a Locked Cutter
1 Do not apply extreme pressure to the moving blade
6 Install the front cover, and then set the power switch to ON
9. Periodical Cleaning
9-1. Cleaning the Thermal Head
9-2. Cleaning the Paper Holder
A-1. General Specifications
Appendix A Specifications
A-5. Option
A-2. Auto Cutter Specifications
A-4. Electrical Characteristics
A-3. Interface
1.0 million cuttings if the paper thickness is 100 µm
A-6. Environmental Requirements
A-7. Reliability
20 million lines based on an average printing rate of
Remarks
A-8. Black Mark Specifications
Appendix B Dip Switch Setting
B-1. Parallel Interface Model
No. 1 2 3 4 5 6 7 DIP-SW1
No. 1 2 3 DIP-SW2
B-2. Sperial Interface RS-232C Model
DIP-SW3
DIP switch
Printer Driver URL
B-3. USB Interface Model
B-4. Ethernet Interface Model
LED Display
Installing the Printer Driver and the LPR Port Driver Set
Green Lights when other party connection is recognized as 10BASE-T
Orange Lights when packets are received
Appendix C Parallel Interface
Table of Connection Signals for Each Mode
Appendix D Serial Interface RS-232C
D-1. RS-232C Connector
DIP SW
D-sub 25 Pin
D-sub 9 Pin
Printer status
D-sub 25 pin
D-3. Electrical Characteristics
D-2. Cable Connections
Host side
E-1. USB Interface Specifications
E-2. Ethernet Interface Specifications
Appendix E USB Interface and Ethernet Interface
Modular plug
Appendix F Buzzer Driver Circuit
Drive circuit
Appendix G Memory Switch Settings
Page
Page
OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC
Related pages
Troubleshooting Procedures for Toshiba A10
Specifications for Marantz DV6400
Indicator lights for AT&T E5908
Structure Diagram for Acnodes PMH 8064
How to connect an alternative plug for Indesit BA 139 PS
Installations Industrielles ET Commerciales for Peavey PV Series
Parts List for Hunter Fan 21337
Additional information Language code list for Pioneer DV-585K-s
Command Reference List for LG Electronics DU-60PY10
How does the
Motorola DR 3000
(#) enhance communication efficiency?
Top
Page
Image
Contents