Star Micronics
TSP1000 Installing the Cable, Install the cable as shown in the diagram below
Specifications
Install
Errors
Connecting USB Cable
D-1. RS-232C Connector
Periodical Cleaning
Non recoverable error
Turning Power On
Switch Blind Installation
Page 17
4-5.
Installing the Cable
Install the cable as shown in the diagram below.
– 13 –
Page 16
Page 18
Image 17
Page 16
Page 18
Contents
USER’S MANUAL
TSP1000 SERIES
THERMAL PRINTER
Page
Statement
Federal Communications Commission Radio Frequency Interference
Statement of The Canadian Department of Communications
Radio Interference Regulations
TABLE OF CONTENTS
1-1. Unpacking
1. Unpacking and Installation
2. Parts Identification and Nomenclature
Choosing a place for the printer
Core inner
3. Consumable Parts and AC Adapter
Core outer
Page
4-1-1. Serial Interface RS-232C Cable
4. Connecting Cables and AC Adapter
4-1. Interface Cable
5 cm maximum Fastener Pull and cut
4-1-2. Parallel Interface Cable
Ferrite core Interface cable
Parallel interface cable
4-1-3. Connecting USB Cable
Ethernet cable
4-1-4. Connecting Ethernet Cable
Ferrite core
10cm
4-2. Connecting to a Buzzer Drive
4-3. Connecting the Optional AC Adapter
Make sure that the AC adapter has been connected as described in
4-4. Turning Power On
Install the cable as shown in the diagram below
4-5. Installing the Cable
4-6. Switch Blind Installation
5-1. Control Panel
Errors
5. Control Panel and Other Functions
4 Paper detection error
3 Non recoverable error
1 If a non recoverable error occurs, turn the power OFF immediately
5-3. Self Printing
1 Push the Cover open lever, and open the printer cover
6. Loading the Roll Paper
Be sure to use roll paper that matches the printer’s specification
Note Make sure that the printer cover is securely closed
1. Do not touch the cutter blade
7. Adjusting the Near-end Sensor
Adjustment value according to the paper you are using
8-2. Removing Paper Jam
8. Preventing and Clearing Paper Jams
8-1. Preventing Paper Jams
8-3. Releasing a Locked Cutter
1 Do not apply extreme pressure to the moving blade
6 Install the front cover, and then set the power switch to ON
9-2. Cleaning the Paper Holder
9. Periodical Cleaning
9-1. Cleaning the Thermal Head
A-1. General Specifications
Appendix A Specifications
A-4. Electrical Characteristics
A-2. Auto Cutter Specifications
A-3. Interface
A-5. Option
A-7. Reliability
A-6. Environmental Requirements
20 million lines based on an average printing rate of
1.0 million cuttings if the paper thickness is 100 µm
Remarks
A-8. Black Mark Specifications
Appendix B Dip Switch Setting
No. 1 2 3 DIP-SW2
B-1. Parallel Interface Model
No. 1 2 3 4 5 6 7 DIP-SW1
B-2. Sperial Interface RS-232C Model
DIP-SW3
DIP switch
Printer Driver URL
B-3. USB Interface Model
B-4. Ethernet Interface Model
Green Lights when other party connection is recognized as 10BASE-T
Installing the Printer Driver and the LPR Port Driver Set
Orange Lights when packets are received
LED Display
Appendix C Parallel Interface
Table of Connection Signals for Each Mode
Appendix D Serial Interface RS-232C
D-1. RS-232C Connector
D-sub 9 Pin
D-sub 25 Pin
Printer status
DIP SW
D-2. Cable Connections
D-3. Electrical Characteristics
Host side
D-sub 25 pin
Appendix E USB Interface and Ethernet Interface
E-1. USB Interface Specifications
E-2. Ethernet Interface Specifications
Modular plug
Appendix F Buzzer Driver Circuit
Drive circuit
Appendix G Memory Switch Settings
Page
Page
OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC
Related pages
All Install page
Unit Installation for Regency L900-1
Problèmes liés à linstallation Mode PC for Samsung LH55CSPLBC/EN
Installation / Operation Instructions Ownership for True Manufacturing Company TMW-36F-QT
Installation for Roadmaster RS525
Install The Filters for System Sensor DH100ACDCLP
Installing or removing the dust cup optional accessory for Makita HR2621
Installation Location for Sanyo KS2432
Safety precautions for installation for Electrolux A 75100 GA3
Installation af USB-driveren til MAC for Samsung EC-S1030BBA/FI
Installation des logiciels Démarrage du mode ordinateur for Samsung EC-PL65ZABP/FR
What are the maintenance tips for the
Asko D3530
?
Top
Page
Image
Contents