Star Micronics SP317 user manual Removing the Roll Paper

Page 12

ENGLISH

			Auto cutter
	Lower	Paper insertion
	paper	Paper insertion
	paper	slit	Upper paper
		slit	Upper paper
		Paper insetion
		slit	Lower paper
	Upper paper
		Print head	Platen
		Print head
		Platen
		Print head

Fig. 2-12 Insertion of the paper into the auto cutter

(When using copying paper) (SP347)

Paper outlet

Auto cutter

Fig. 2-13 Paper outlet of the front cover

(SP347)

CPull on the edge of the paper to remove any slack and then lower the

auto cutter.

DInsert the paper through the front

cover paper outlet and then replace the front cover by reversing the re- moval steps.

ETo install the rear cover reverse the removal steps.

2-3. Removing the Roll Paper

Remove the rear cover then cut off the paper near the rear of the paper guide. Then press the “FEED” switch to feed out the rest of the paper that is remaining in the unit.

When the paper runs out, a buzzer will sound four times per cycle for two cycles. NOTE 1. Press the “FEED” switch to remove the rest of the paper that is in

the printer. (If you remove the paper by hand, the paper could wrinkle or slip causing it to jam.)

NOTE 2. When the paper end mark appears on the paper, replace the roll paper before it runs out.

– 10 –

Image 12

Contents SP317/347F EC Council Directive 89/336/EEC of 3 May Table of Contents Turn the power switch on the printer to the off position Loading the Ribbon CartridgeTo the off position To remove the front cover lift it upApprox cm. and pull it forward Immediately after printingTion until you hear a locking sound Insert the ink ribbon betweenProtruding beyond the ribbon sepa RatorLoading the Paper Removing the rear cover SP317Setting of the paper guide SP317 Removing the rear cover SP347 Position of the adjust lever SP347 10 Loading the paper SP347 Removing the Roll Paper LED flashes Validation printing mode is set Control PanelPage Table DES Matières Installation D’UNE Cartouche DE Ruban Dépose du cache avant SP347 OK NON Chargement DU Papier Montage des attaches pour Rouleau de papier SP317Avancer le papier Positionnement des guides de Papier SP317Vez-le d’environ 3 cm, puis tirez-le vers l’avant PoucesPositionnement du levier d’ajus 10 Chargement du papier SP347 Enlèvement d’un rouleau de papier Panneau DE Commande Touche en ligne on LinePage Inhaltsverzeichnis Einlegen DER Farbbandkassette Abb -3 Abnehmen der Frontabdeckung SP347 Ten. Die Farbbandkassette aus die Ser Position bis zum hörbaren EinRasten Eindrücken. Das Farbband Zwischen dem Druckkopf und demEinlegen DES Papiers Den Netzschalter des Druckers in Aus-Stellung stellenEinzuziehen Diese ca cm anheben und nach vorne ziehen Stellen Sie Die linke und rechte Mm großen Abstand zwischenDer Papierführung und der Kante Des Papiers und befestigen Sie denDeutsch Automatische Abschneideinheit Unteres Papier Bedienfeld Taste on LinePage Indice Caricamento Della Cartuccia DEL Nastro Rimozione del coperchio anteriore SP347 Okno Caricamento Della Carta Regolazione delle guide della Carta SP317 Rimozione del coperchio poste Riore SP347 Posizione della leva di 10 Caricamento della carta SP347 Rimozione della carta in rotolo Pannello DI Controllo Interruttore on LinePage Appendix RS-232CMA current loop option RS-422A optionInterface Connections Serial Intefface Connectors and Signals Parallel Interface This connector mates with an Amphenol 57-30360 connectorDrive output 24V, max .0 a Dot Alignment Adjust Mode Select the printing status one line down when pressed onceAppendix General Specifications CharactersAppendix Tion 169 W × 330 D × 170 H m Approx .3 kg169 W × 330 D × 176 H mm Approx 4.6 kg Memo Overseas Subsidiary Companies Star Micronics AMERICA, INC