Star Micronics user manual Setting of the paper guide SP317

Page 8

ENGLISH

Fig. 2-3 Setting of the paper guide

(SP317)

Fig. 2-4 Loading the paper (SP317)

5Set the left and right paper guides. Leave a 0.5 mm gap between the paper guide and the edge of the paper and fix the lock lever.

∙When you insert the stop ring that corresponds to the groove of the paper guide shaft shown in Fig. 2- 3, that will be the position when you set the paper guide.

6Turn the power switch on the printer

to the on position.

7Cut off the front edge of the roll paper in a straight line.

In case the front edge of the paper is fastened with a label, etc. remove the adhesive part of the label. If any

adhesive remains on the paper, it will stick onto the roller of the printer, causing the paper to misfeed.

8Hold the roll paper as shown in the illustration, then insert the top end

of the paper beneath the paper guide as far as it will go and press the “FEED” switch on the control panel to feed the paper.

9When the front edge of the paper

feeds out of the printer, release the “FEED” switch. Next, insert the rollpaper into the roll paper shaft, and set the roll paper shaft on to the shaft holder.

0Insert the top edge of the paper into the tear bar slot, then mount the rear cover by reversing the procedure for removing the rear cover in step 3 above.

NOTE: When the paper end mark appears on the paper, re- place the roll paper before it runs out.

– 6 –

Image 8

Contents SP317/347F EC Council Directive 89/336/EEC of 3 May Table of Contents Turn the power switch on the printer to the off position Loading the Ribbon CartridgeTo the off position To remove the front cover lift it upApprox cm. and pull it forward Immediately after printingTion until you hear a locking sound Insert the ink ribbon betweenProtruding beyond the ribbon sepa RatorLoading the Paper Removing the rear cover SP317Setting of the paper guide SP317 Removing the rear cover SP347 Position of the adjust lever SP347 10 Loading the paper SP347 Removing the Roll Paper LED flashes Validation printing mode is set Control PanelPage Table DES Matières Installation D’UNE Cartouche DE Ruban Dépose du cache avant SP347 OK NON Chargement DU Papier Montage des attaches pour Rouleau de papier SP317Avancer le papier Positionnement des guides de Papier SP317Vez-le d’environ 3 cm, puis tirez-le vers l’avant PoucesPositionnement du levier d’ajus 10 Chargement du papier SP347 Enlèvement d’un rouleau de papier Panneau DE Commande Touche en ligne on LinePage Inhaltsverzeichnis Einlegen DER Farbbandkassette Abb -3 Abnehmen der Frontabdeckung SP347 Ten. Die Farbbandkassette aus die Ser Position bis zum hörbaren EinRasten Eindrücken. Das Farbband Zwischen dem Druckkopf und demEinlegen DES Papiers Den Netzschalter des Druckers in Aus-Stellung stellenEinzuziehen Diese ca cm anheben und nach vorne ziehen Stellen Sie Die linke und rechte Mm großen Abstand zwischenDer Papierführung und der Kante Des Papiers und befestigen Sie denDeutsch Automatische Abschneideinheit Unteres Papier Bedienfeld Taste on LinePage Indice Caricamento Della Cartuccia DEL Nastro Rimozione del coperchio anteriore SP347 Okno Caricamento Della Carta Regolazione delle guide della Carta SP317 Rimozione del coperchio poste Riore SP347 Posizione della leva di 10 Caricamento della carta SP347 Rimozione della carta in rotolo Pannello DI Controllo Interruttore on LinePage Appendix RS-232CMA current loop option RS-422A optionInterface Connections Serial Intefface Connectors and Signals Parallel Interface This connector mates with an Amphenol 57-30360 connectorDrive output 24V, max .0 a Dot Alignment Adjust Mode Select the printing status one line down when pressed onceAppendix General Specifications CharactersAppendix Tion 169 W × 330 D × 170 H m Approx .3 kg169 W × 330 D × 176 H mm Approx 4.6 kg Memo Overseas Subsidiary Companies Star Micronics AMERICA, INC