Star Micronics SP317 user manual Removing the rear cover SP347

Page 9

2-2. SP347

Rear cover

Power off

1Turn the power switch on the printer to the off position.

2To remove the front cover lift it up approx. 3cm. and pull it forward.

NOTE: Do not touch the print head immediately after printing as it can be extremely hot.

3To remove the rear cover lift it up approx. 3cm and push it backwards.

ENGLISH

Fig. 2-5 Removing the rear cover (SP347)

4Adjust DIP switch 2-4, the roll paper holder and the adjust lever position according to the width and thickness of the roll paper that is being used.

∙Refer to Installation Manual in regard to the position of the DIP switch.

∙If you do not know the standard position of the adjust lever, lower the adjust lever as far as it will go (on the rear cover side), and then pull it two positions. That position is standard position A.

	Paper		DIP switch 2-4	Adjust lever	Roll paper holder
	Paper width	Thickness	(Fig. 4-1)	position (Fig. 2-6)	(Fig. 2-7)

	2.25 inches	1 sheet of paper	OFF	A	Used (Inner groove)

		Printer paper	OFF	B	Used (Inner groove)
		Printer paper	OFF	B	Used (Inner groove)

	3.0 inches	1 sheet of paper	ON	A	Used (Outer groove)

		Printer paper	ON	B	Used (Outer groove)
		Printer paper	ON	B	Used (Outer groove)

	3.25 inches	1 sheet of paper	ON	A	Not used

		Printer paper	ON	B	Not used
		Printer paper	ON	B	Not used

– 7 –

Image 9

Contents SP317/347F EC Council Directive 89/336/EEC of 3 May Table of Contents Loading the Ribbon Cartridge Turn the power switch on the printer to the off positionTo remove the front cover lift it up To the off positionApprox cm. and pull it forward Immediately after printingInsert the ink ribbon between Tion until you hear a locking soundProtruding beyond the ribbon sepa RatorRemoving the rear cover SP317 Loading the PaperSetting of the paper guide SP317 Removing the rear cover SP347 Position of the adjust lever SP347 10 Loading the paper SP347 Removing the Roll Paper Control Panel LED flashes Validation printing mode is setPage Table DES Matières Installation D’UNE Cartouche DE Ruban Dépose du cache avant SP347 OK NON Montage des attaches pour Rouleau de papier SP317 Chargement DU PapierPositionnement des guides de Papier SP317 Avancer le papierPouces Vez-le d’environ 3 cm, puis tirez-le vers l’avantPositionnement du levier d’ajus 10 Chargement du papier SP347 Enlèvement d’un rouleau de papier Touche en ligne on Line Panneau DE CommandePage Inhaltsverzeichnis Einlegen DER Farbbandkassette Abb -3 Abnehmen der Frontabdeckung SP347 Ser Position bis zum hörbaren Ein Ten. Die Farbbandkassette aus dieRasten Eindrücken. Das Farbband Zwischen dem Druckkopf und demDen Netzschalter des Druckers in Aus-Stellung stellen Einlegen DES PapiersEinzuziehen Diese ca cm anheben und nach vorne ziehen Mm großen Abstand zwischen Stellen Sie Die linke und rechteDer Papierführung und der Kante Des Papiers und befestigen Sie denDeutsch Automatische Abschneideinheit Unteres Papier Taste on Line BedienfeldPage Indice Caricamento Della Cartuccia DEL Nastro Rimozione del coperchio anteriore SP347 Okno Caricamento Della Carta Regolazione delle guide della Carta SP317 Rimozione del coperchio poste Riore SP347 Posizione della leva di 10 Caricamento della carta SP347 Rimozione della carta in rotolo Interruttore on Line Pannello DI ControlloPage RS-232C AppendixRS-422A option MA current loop optionInterface Connections Serial Intefface This connector mates with an Amphenol 57-30360 connector Connectors and Signals Parallel InterfaceDrive output 24V, max .0 a Select the printing status one line down when pressed once Dot Alignment Adjust ModeAppendix Characters General SpecificationsAppendix 169 W × 330 D × 170 H m Approx .3 kg Tion169 W × 330 D × 176 H mm Approx 4.6 kg Memo Overseas Subsidiary Companies Star Micronics AMERICA, INC