TRENDnet TPL310AP manual Wireless Access Point Initial Setup

Page 13

Chapter 2: Wireless Access Point Initial Setup

When installing the TPL-310AP for the first time, it required for you to configure the device from a wired computer. Since the default IP address of the TPL-310AP is 192.168.10.100, please make sure to assign an IP address to the TPL-310AP that is NOT assigned to any other devices on your net- work. If your network IP address range is NOT 192.168.10.x, then the TPL-310AP IP address should be assigned with your network’s IP address range (i.e. 192.168.1.x, 192.168.2.x, 192.168.0.x) This chapter covers the typical configuration of the TPL-310AP in Access Point (AP) mode using the Setup Wizard. If you are an experienced user, other web configuration settings can be referenced in Chapter 3. Once the initial setup is complete, Chapter 4 will cover creating a powerline network with one additional po- werline adapter, or adding the TPL-310AP to existing powerline network.

1.Plug the TPL-310AP into an available power outlet within reach of your computer’s network ca- ble.

2.Connect a network cable from the TPL-310AP Wireless Access Point’s network port (located at the bottom of the device) into the computer’s network port.

3.Move the power switch (located at the top of the device) to the “On” position.

4.Assign a static IP address to your computer’s network adapter to 192.168.10.10 and subnet mask 255.255.255.0.

Windows 7: Click on the Start Button, select Control Panel, click Network and Internet, click on Network and Sharing Center, and click Change Adapter Settings. Then, right-click the Local Area Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and then click Properties. Select Use the following IP address, and manually enter the IP address settings.

Windows Vista: Click on the Start Button, select Control Panel, click Network and Internet, click on Network and Sharing Center, and click Manage Network Connections. Then, right-click the Local Area Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and then click Properties. Select Use the following IP address, and manually enter the IP address set- tings.

Windows XP/2000: Click on the Start Button, select Control Panel, double-click the Network Connections icon, and then click Properties. Click Internet Protocol (TCP/IP) and then click Prop- erties. Select Use the following IP address, and manually enter the IP address settings.

5.Open your Web browser, and type http://192.168.10.100 in the Address bar, and then press En- ter.

Image 13
Contents Page Safety RoHS Table of Contents Overlapping Powerline Networks Product Overview Expanding a Wireless Network Expanding an Existing Powerline NetworkExpanding a Wired Network Powerline Technical FeaturesWireless System Requirements Package ContentsMemory LEDs & Buttons Device LabelLED Wireless AP Setting IP Address / Subnet Mask 192.168.10.100 Defaults SettingsTop Panel TRENDnet310Wireless Access Point Initial Setup Page Page Page Page Page Default Configuration Settings Wireless Access Point Web Management InterfaceWireless AP Setting Menu ItemsStatus Basic Settings Wireless Apply/Reset ChangesDescription of Modes AP+WDS Access Point + Wireless Distribution System AllowsNetwork Type Control SidebandMultiple Ssid Advanced Settings Active Wireless Client TableSecurity WEP Security 802.1x AuthenticationWPA/WPA2 Security WPA / WPA2 Cipher Suite WPA MixedPre-Shared Key Format Wireless Access Control Access ControlCurrent Access Control CommentItems Information MAC Address WDS SettingsCurrent WDS AP List Items Information Mesh ID Mesh SettingsSite Survey 11 WPS Schedule Items Information Enable Wireless ScheduleDays Sun, Mon, Tue, Wed, Thu, Fri, Sat Check TimeItems Information IP Address TCP/IP Settings802.1d Spanning Tree Clone MAC AddressEnable Remote Log Enable LogLog Types of LoggingSave/Reload Settings Upgrade FirmwareStatistics System Time PasswordLogout Powerline Create a powerline network and extend you wireless network Page Changing the Network Name/Security Key using the Sync Button Securing your Powerline NetworkPage Overlapping Powerline Networks Page Software Installation Powerline Configuration UtilityPage Page Confirm Installation window, click Next Upgrade Firmware Using the UtilityPage Powerline TroubleshootingWireless Installation Considerations Specifications Output Power Access Point ModesFrequency Band AntennaLimited Warranty PWP05202009v2