TRENDnet TPL310AP Access Point Modes, Frequency Band, Antenna, Output Power, Receiver Sensitivity

Page 55

Wireless

Modulation

OFDM with BPSK, QPSK, 16QAM, and 64QAM

 

 

Access Point Modes

Access Point (AP)

 

Access Point (AP) Client (wireless adapter)

 

Wireless Distribution System (WDS)

 

Wireless Distribution System (WDS) with Access Point (AP)

 

Mesh

 

Mesh with Access Point (AP)

 

Repeater (using AP mode only)

 

 

Frequency Band

2.412GHz ~ 2.472GHz

 

 

Data Rate***

802.11b: 1,2,5.5, and 11Mbps

 

802.11g: 6,9,12,18,24,36,48 and 54Mbps

 

802.11n: up to 300 Mbps

 

 

Security

64/128-Bit WEP (HEX & ASCII), WPA/WPA2 RADIUS, WPA/WPA2-

 

PSK

 

 

Antenna

2 x 2dBi internal printed dipole antennas

 

 

Channel

2.4GHz: 1~11 (FCC), 1~13 (ETSI)

 

 

Output Power

16dBm typically @ 802.11b

 

14dBm typically @ 802.11g

 

13dBm typically @ 802.11n

 

 

Receiver Sensitivity

802.11n Typical -68 dBm

 

802.11g Typical -73 dBm

 

802.11b Typical -84 dBm

 

 

*Maximum of 16 adapters (nodes) recommended for streaming video across your network. Additional adapters may decrease performance.

**200Mbps is the maximum theoretical Powerline data rate. Actual throughput will vary depending on environment.

***Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions.

****Networked Powerline devices need to be plugged into power outlets that are on the same elec- trical system.

*****It is not recommended to use this product on electrical systems that use AFCI circuit breakers or plugged into GFI protected outlets as this may cause performance degradation or loss in connectivity.

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Page Safety RoHS Table of Contents Overlapping Powerline Networks Product Overview Expanding a Wireless Network Expanding an Existing Powerline NetworkExpanding a Wired Network Powerline Technical FeaturesWireless System Requirements Package ContentsMemory LEDs & Buttons Device LabelLED TRENDnet310 Defaults SettingsWireless AP Setting IP Address / Subnet Mask 192.168.10.100 Top PanelWireless Access Point Initial Setup Page Page Page Page Page Menu Items Wireless Access Point Web Management InterfaceDefault Configuration Settings Wireless AP SettingStatus Basic Settings Wireless Apply/Reset ChangesControl Sideband AP+WDS Access Point + Wireless Distribution System AllowsDescription of Modes Network TypeMultiple Ssid Advanced Settings Active Wireless Client TableSecurity WEP Security 802.1x AuthenticationWPA/WPA2 Security WPA / WPA2 Cipher Suite WPA MixedPre-Shared Key Format Comment Access ControlWireless Access Control Current Access ControlItems Information MAC Address WDS SettingsCurrent WDS AP List Items Information Mesh ID Mesh SettingsSite Survey 11 WPS Time Items Information Enable Wireless ScheduleSchedule Days Sun, Mon, Tue, Wed, Thu, Fri, Sat CheckClone MAC Address TCP/IP SettingsItems Information IP Address 802.1d Spanning TreeTypes of Logging Enable LogEnable Remote Log LogSave/Reload Settings Upgrade FirmwareStatistics System Time PasswordLogout Powerline Create a powerline network and extend you wireless network Page Changing the Network Name/Security Key using the Sync Button Securing your Powerline NetworkPage Overlapping Powerline Networks Page Software Installation Powerline Configuration UtilityPage Page Confirm Installation window, click Next Upgrade Firmware Using the UtilityPage Powerline TroubleshootingWireless Installation Considerations Specifications Antenna Access Point ModesOutput Power Frequency BandLimited Warranty PWP05202009v2
Top Page Image Contents