TRENDnet TPL310AP manual TCP/IP Settings, Items Information IP Address, 802.1d Spanning Tree

Page 35

3.5 TCP/IP Settings

This page is used to configure the IP address parameters of the wireless access point for the local area network, which connects to the Ethernet port of your wireless access point. Please make sure that the IP address assigned to the wireless access point is available and is not being used by any other device connected to the local area network.

Items

Information

 

 

IP Address

The IP of your AP LAN port (default

192.168.10.100).

 

 

 

 

Subnet Mask of you LAN (default 255.255.255.0).

Subnet Mask

All devices on the network must have the same

 

subnet mask to communicate on the network.

 

 

Default Gateway

Enter the IP Address of the AP in your network.

 

 

 

DHCP stands for Dynamic Host Configuration

 

Protocol. It is a protocol for assigning dynamic IP

DHCP

addresses “automatically”. In this device, manual

 

setting up your client IP is necessary when you

 

want to use the AP as your client’s default gateway.

 

 

 

Enabled: Suitable for office environment, for exam-

 

ple, there are over 3 Ethernet switches or Routers or

 

APs are being used at the same time. Because STP

802.1d Spanning Tree

(Spanning Tree Protocol) needs 2~49 seconds to take

effect.

(STP)

Disabled: Suitable for ordinary application when

 

 

there are less than 3 Ethernet switches or Routers or

 

APs working the same time, for example, ordinary

 

home.

 

 

 

Applies to Client mode only. Enter the MAC address

 

you would like to clone to the TPL-310AP. This will

 

be the MAC address that will appear on the access

Clone MAC Address

point or wireless router you are connected to when

in Client mode. If there is no value here, then the

 

 

TPL-310AP MAC address will be used unless Enable

 

MAC Clone is check under Wireless > Basic Settings.

 

Section 3.4.2 (MAC Address Format: xxxxxxxxxxxx)

 

 

*Please click on the Apply Changes button or the Reset button at the bottom to save/reset the configu- ration.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Page Safety RoHS Table of Contents Overlapping Powerline Networks Product Overview Expanding a Wired Network Expanding an Existing Powerline NetworkExpanding a Wireless Network Wireless Technical FeaturesPowerline Memory Package ContentsSystem Requirements LEDs & Buttons Device LabelLED TRENDnet310 Defaults SettingsWireless AP Setting IP Address / Subnet Mask 192.168.10.100 Top PanelWireless Access Point Initial Setup Page Page Page Page Page Menu Items Wireless Access Point Web Management InterfaceDefault Configuration Settings Wireless AP SettingStatus Basic Settings Wireless Apply/Reset ChangesControl Sideband AP+WDS Access Point + Wireless Distribution System AllowsDescription of Modes Network TypeMultiple Ssid Advanced Settings Active Wireless Client TableSecurity WEP Security 802.1x AuthenticationWPA/WPA2 Security Pre-Shared Key Format WPA MixedWPA / WPA2 Cipher Suite Comment Access ControlWireless Access Control Current Access ControlCurrent WDS AP List WDS SettingsItems Information MAC Address Items Information Mesh ID Mesh SettingsSite Survey 11 WPS Time Items Information Enable Wireless ScheduleSchedule Days Sun, Mon, Tue, Wed, Thu, Fri, Sat CheckClone MAC Address TCP/IP SettingsItems Information IP Address 802.1d Spanning TreeTypes of Logging Enable LogEnable Remote Log LogStatistics Upgrade FirmwareSave/Reload Settings Logout PasswordSystem Time Powerline Create a powerline network and extend you wireless network Page Changing the Network Name/Security Key using the Sync Button Securing your Powerline NetworkPage Overlapping Powerline Networks Page Software Installation Powerline Configuration UtilityPage Page Confirm Installation window, click Next Upgrade Firmware Using the UtilityPage Powerline TroubleshootingWireless Installation Considerations Specifications Antenna Access Point ModesOutput Power Frequency BandLimited Warranty PWP05202009v2
Top Page Image Contents