Xantrex Technology PH1800 manual Electrical Specifications

Page 50

Specifications

Electrical Specifications

Table A-1Electrical Specifications for the Inverter

Parameter

PowerHub 1800 Inverter

 

 

Maximum Output Power

1800 W (15A) (5 minutes maximum)

 

 

Continuous Output Power

1440 W (12 A)

 

 

Surge Rating

2880 W (24 A)

 

 

Input Voltage Range

10.5 to 15.0 Vdc

 

 

Input Frequency Range

60 Hz

 

 

Peak Efficiency

88%

 

 

System Shutdown Mode

< 12 W

(Display On)

 

 

 

Idle Mode

<1.5 W

 

 

Output Frequency

60 Hz / ±1 Hz

 

 

Output Waveform (resistive load)

Modified sine wave (>30% THD)

 

 

Output Voltage (at no load)

110 to 125 Vac

 

 

Low Battery Cutout

10.5 Vdc with < 240 W load and 11.0 V with > 240 W load

 

 

High Battery Cutout

15.0 Vdc

 

 

Transfer Relay Rating

20 A

 

 

Transfer Time AC to Inverter

< 40 ms

 

 

AC Qualification Time

~ 20 seconds

 

 

Protection

• Five 20 A/32 Vdc fuses protecting the 80A/1000 W DC input

 

terminal.

 

• Two 20 A/32 Vdc fuses protecting 32A/ 400 W DC input

 

terminal.

 

• One 15 Aac supplemental protector.

 

• One 1 A/250 Vac fuse for system ground fault protection.

 

 

Table A-2Electrical Specifications for the Battery Box

Parameter

Protection

Battery Box1

Ten 20 A/32 Vdc Fuses for short circuit and reverse polarity conditions.

1.Stand-alone battery box Xantrex Part Number: PH1800-BBX

A–2

975-0288-01-01

Image 50
Contents PowerHub Page PowerHub Operator’s GuideDate and Revision Scope About This GuidePurpose AudienceRelated Information Conventions UsedAbbreviations and Acronyms Important Safety Instructions Figure i Basic Safety Precautions When Working With Batteries Precautions for Using Rechargeable Appliances FCC/ICES 003 Information to the UserPower Down Procedure To Power Down the PowerHubIf hardwired...... To Power Down the PowerHub Contents Troubleshooting SpecificationsFigures Xiv Tables Page Introduction For this topic SeeIntroduction Principles of Inverter OperationBasic Functions of the PowerHub Primary AC sourceInverter Features 2PowerHub 1800 FeaturesBattery Charger Features Three-Stage Charging Process onVoltage 12.5 Vdc Contains information on operating the PowerHub Operation8.8 Inverter Control PanelUser Controls and Display LEDOperating Mode LEDs Status LEDsSelecting Charger Settings AC LEDPower On and Off Basic OperationChanging the Display 3Input Displays4Output Displays Changing Charging Settings AC is not availableConnecting AC Loads 6Connecting AC Loads Loads that should not be used with the PowerHub Typical Loads that might be used with the PowerHubLoads That Might Not Work Well With the PowerHub Troubleshooting How to Troubleshoot the PowerHub Error Codes Troubleshooting Error Codes for Troubleshooting the PowerHub If Utility Power is not Available 2Possible Problems if Utility Power is Not AvailableError code E02 If Utility Power is Available 3Possible Problems if Utility Power is AvailablePossible Problem Loads Rechargeable Devices Ground Fault Protection Replacing the Ground Fault Protection Fuse1Replacing Ground Fault Protection Fuse Page Specifications Electrical Specifications Table A-1Electrical Specifications for the InverterPhysical Specifications Battery Charger SpecificationsFigure A-1Three-Stage Charging Process Charging Profiles Amp Charging ProfileTable A-610-amp Charging Profile Index IX-2 975-0288-01-01 Warranty and Return Information WarrantyDisclaimer ProductExclusions Return Material Authorization PolicyReturn Procedure Out of Warranty Service Information About Your System Purchased From Purchase DateWA-6 Page Xantrex Technology Inc