Xantrex Technology PH1800 manual Error Codes

Page 39

Error Codes

Error Codes

The following error codes may be displayed on the LED display if the described fault conditions occur.

Table 3-1

Error Codes for Troubleshooting the PowerHub 1800

 

Error Code

 

Description

 

 

 

 

 

 

 

Displayed

 

of Error

Description of Condition

 

Resolution

 

 

 

 

 

 

E01

 

DC Input

Unit shuts down.

 

The unit will automatically

 

 

Under Voltage

The input voltage has dropped to below

 

reset once the fault condition is

 

 

Shutdown

the operation voltage limit of 11.0 to

 

removed.

 

 

 

 

If this condition is not corrected

 

 

 

10.5 V.

 

 

 

 

 

and the unit powers down

 

 

 

An alarm continues to beep once every

 

 

 

 

 

completely, it will be necessary

 

 

 

second until input/output voltage drops to

 

to press the ON/OFF Button to

 

 

 

10.3 V.

 

turn the unit ON again.

 

 

 

The alarm will continue to beep once

 

 

 

 

 

every 30 seconds until battery voltage

 

 

 

 

 

reaches 10.0 V . If the battery reaches

 

 

 

 

 

10.0 V, the display turns OFF and the unit

 

 

 

 

 

powers down completely.

 

 

 

 

 

 

 

 

E02

 

DC Input

Unit shuts down.

 

The unit will automatically

 

 

Over Voltage

An input voltage is greater than 15 V.

 

reset once the fault condition is

 

 

Shutdown

 

removed.

 

 

The alarm will continue to beep once

 

 

 

 

 

 

 

 

 

every second.

 

 

 

 

 

 

 

 

E03

 

AC Output

Unit shuts down.

 

Remove excess AC loads.

 

 

Overload

An AC load applied to the system in

 

Reset of unit is required.

 

 

Shutdown

 

To reset the unit, turn it OFF

 

 

inverter mode is above operation limit.

 

 

 

 

 

and back ON.

 

 

 

 

 

 

 

 

 

 

 

E04

 

System Over

Unit shuts down.

 

Reduce loads or reduce ambient

 

 

Temperature

System internal temperature is above

 

temperature around the

 

 

Shutdown

 

PowerHub.

 

 

operation limit.

 

 

 

 

 

The unit will automatically

 

 

 

The alarm will continue to beep once

 

 

 

 

 

reset once the unit cools down

 

 

 

every second.

 

and reaches a safe operating

 

 

 

 

 

temperature.

 

 

 

 

 

 

E05

 

DC Input

System is still operating but input voltage

 

Unit continues to run.

 

 

Under Voltage

has dropped too close to the shutdown

 

If the warning is ignored, the

 

 

Alarm

limit (11.0 to 10.5 Vdc).

 

unit will eventually goes to the

 

 

 

Alarm will beep once every two seconds

 

E01 fault condition.

 

 

 

 

 

 

 

 

until the warning condition is removed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

975-0288-01-01

3–3

Image 39
Contents PowerHub Page Operator’s Guide PowerHubDate and Revision Audience About This GuidePurpose ScopeConventions Used Abbreviations and AcronymsRelated Information Important Safety Instructions Figure i Basic Safety Precautions When Working With Batteries FCC/ICES 003 Information to the User Precautions for Using Rechargeable AppliancesTo Power Down the PowerHub Power Down ProcedureIf hardwired...... To Power Down the PowerHub Contents Specifications TroubleshootingFigures Xiv Tables Page For this topic See IntroductionPrinciples of Inverter Operation IntroductionPrimary AC source Basic Functions of the PowerHub2PowerHub 1800 Features Inverter FeaturesThree-Stage Charging Process on Battery Charger FeaturesVoltage 12.5 Vdc Operation Contains information on operating the PowerHubInverter Control Panel 8.8LED User Controls and DisplayStatus LEDs Operating Mode LEDsAC LED Selecting Charger SettingsBasic Operation Power On and Off3Input Displays Changing the Display4Output Displays AC is not available Changing Charging SettingsConnecting AC Loads 6Connecting AC Loads Typical Loads that might be used with the PowerHub Loads That Might Not Work Well With the PowerHubLoads that should not be used with the PowerHub Troubleshooting How to Troubleshoot the PowerHub Error Codes Troubleshooting Error Codes for Troubleshooting the PowerHub 2Possible Problems if Utility Power is Not Available If Utility Power is not AvailableError code E02 3Possible Problems if Utility Power is Available If Utility Power is AvailablePossible Problem Loads Rechargeable Devices Replacing the Ground Fault Protection Fuse Ground Fault Protection1Replacing Ground Fault Protection Fuse Page Specifications Table A-1Electrical Specifications for the Inverter Electrical SpecificationsBattery Charger Specifications Physical SpecificationsFigure A-1Three-Stage Charging Process Amp Charging Profile Charging ProfilesTable A-610-amp Charging Profile Index IX-2 975-0288-01-01 Warranty Warranty and Return InformationProduct DisclaimerReturn Material Authorization Policy Return ProcedureExclusions Out of Warranty Service Purchased From Purchase Date Information About Your SystemWA-6 Page Xantrex Technology Inc