Xantrex Technology XMP 2600 manual Mon, Ocrst

Page 66

Commands and Queries Reference			Alphabetical reference
MON	change the	operating mode of the RS232 serial communication
	interface into or out of Monitor Mode.
	Syntax	MON <int>
	Parameters	the requested mode of operation for the RS232 serial
		interface. A value of “0” will turn Monitor Mode
		off. A value of “1” will turn it on.
	Category	System	Type: Overlapped
MON?	return the current state of the Monitor Mode. A value of “0” means
	that Monitor Mode is off. A value of “1” indicate that the Monitor
	Mode is on.
	Syntax	MON?
	Parameters	none
	Category	System	Type: Sequential
OCRST	see OVRST
OCSET	program the Power Module’s Over Current Protection.
	Syntax	OCSET <ch>,<value>
	Parameters	the number of the Power Module to be programmed.
		the value to be assigned to the OCP threshold. A
		value can only be programmed when PROT mode is
		Manual. The upper limit of the Programmed value is
		IMAX + 1. The lower limit of the programmed
		value is ISET.
	Category	Protection	Type: Sequential
OCSET?	return the current programmed value of the Power Module’s OCP
	threshold. The result is a <value>.
	Syntax:	OCSET? <ch>
	Parameters	the number of the channel to be queried.
	Category	Protection	Type: Sequentail
OPT?	return the Options Byte of the Power Module. The result is a decimal
	value in the range 0 to 255 representing bits of the Options Byte.
	For now only three bits have meaning:
	Bit 4 is cleared when the Power Module has the output
	disconnect relay option.
	Bit 5 is cleared if the Power Module has the polarity reversal
	relay option.
	Bit 3 is set if this module has power monitoring logic (e.g. 1/8wide
	36V/40A module)
	Syntax	OPT? <ch>
	Parameters	the number of the channel to be queried.
	Category	Status	Type: Sequential

XMP 2600 Programming Manual rev. 1.1

53

Image 66

Contents Xantrex Multiple Output Power System XMP XMP Warranty Limited What does this warranty cover and how long does itHow do you get service? Last?What does this warranty not cover? Disclaimer ProductInformation About Your Power Supply InformationSafety Summary Description Power Supply SymbolsPower Supply Grounding Do Not Open The Unit Air Inlets And Air Outlet Input Mains Voltage RatingOutput Voltages Nonoperative ModulesPower Supply Safety Regulatory Approvals and Safety Agency ComplianceSafety Agency Compliance Regulatory ApprovalsAbout this manual Chapters TerminologyWho should use this manual Table of contents Basic Programming Commands and Queries Reference Error Codes summary Byte1Interfacing XMP Gpib interfaceSerial interface ACKProgramming messages formats Listening FormatsTalking Formats Response Data SeparatorUsing the Gpib bus How to communicate with the XMPUsing the comm. channels Using an RS232 linkUsing commands Recovering from communication haltsUsing queries Programming the XMPRecommendations on using the XMP Initialize the XMPQuery installed Power Modules Enforce power-on conditionsSetup the XMP 2600 status system Identify the XMPSetup system level protection shutdown features Initial setup of the Power ModulesActivation Protection setupOutput settings Status reportingOn-going usage of the XMP Using advanced featuresHandling SRQ and the IEEE488.2 Status Structures Use queriesEvent registers Event enable registersStatus registers Mask registersOutput message Queue Main status byteMain controller events Responding to SRQ eventsRemote communication time out Summary of power modules statusPower modules status structure Primary engine status structureFaults Register What happens when power is turned onError Code Events RegisterUsage Guidelines Basic setup and usage Output SetupPower Module output rating Overview of output setup parametersOutput activation Output settingsOutput control Globally enabling the outputsFoldback Voltage / current modeCurrent limiting schemes Polarity and disconnect relaysShutdown on current limit Reprogramming DelayRetry Linear foldbackBasic Programming Usage guidelines Setting the window thresholdsWorkpoint window warning Enabling the window thresholdsVoltage mode example Using the events mechanismUsing the warnings Checking the statusAdditional usages Protection using the workpoint windowLoad protection OVPSet output to stored values Arm, trigger, sync and rampTrigger mechanism Toggle the output state on/offSync output What is output ramping? Output rampingOutput ramping initiation Output ramping setupSynchronization of operations Simultaneous operationsOther operations Using hardware Trig and Sync to serialize operationsOutput on/off Sequential OperationsUsing software OPC mechanism to serialize operations Controller notification of Operation CompleteShutdown grouping single, group, global Commands to program shutdown groupingSelective shutdown Different shutdown grouping of modulesShutdown on non-fault events Responding to communication time out eventsComm. time out Turn-on and reset behavior Time out events as reflected in the status structureIeee 488.1 BUS Commands System Commands QueriesCategories GLBL? ResetGlbl GpibSettings Commands Queries Output Control Protection Commands Queries Trigger Sync Commands QueriesRead-Back Queries Status Reporting Commands Queries Synch Alphabetical reference MnemonicParameters None Category System Type Sequential PRE Stores settings of all the Power Modules same as STO command Result register Syntax Return two decimal numbers, in the range 0 to 255. Each bit Cmask Close relay and a value of 1 is returned for an open relay Remove a user message from the XMP 2600 front panel display Set-up the operating mode of the XMP 2600. Re-calculate rqs Response is a series of values one for each installed Power Return output Current measurement of the Power Module. Return the state of the XMP 2600 Local Lock Flag. a value Ocrst Decimal value in the range 0 to Syntax Presence of the Polarity Reversal Relay Option Parameters None Category Settings Type Sequential Master mainframe. For the XMP 2600 this value is String in the following format mssnnn where m=minutes Result is two decimal numbers the first being the level 0t o SN? = Goto = OFF= Stop Module. Result is a decimal number in the range 0 to Shut-down when a remote communication time out occurs. Time out feature Syntax Minus sigh Syntax VLIM? Vset Commands and Queries Reference Ieee 488.2 compatible Status Structures Events RegisterEvents Enable Register Faults RegisterError Code Output RegisterEvents Filtering Positive Mask Register Events Filtering Negative Mask RegisterStandard Event Status Register read with *ESR? PON CME EXE DDE QYE OPCPrimary Status Register read with PSR? Primary Event Status Register read with PER?Status Byte Register read with *STB? PrimerrPower Modules Self Test ResultsByte Main ControllerErrors Detected by the Main Controller Error Codes summaryPower Modules Errors Reported by the Power Module Main Power Modules Communications errorsRS232 Communications errors Gpib Communications errorsParser and Execution errors Status reporting Xantrex Technology Inc