Xantrex Technology XFR 2800 manual Shipped, Configuration, Mode

Page 61

		Local Operation
		Standard Operation
Shipped	The factory ships units already configured for local control (front panel) operation.
Configuration	See Table 3.1 for a summary of this configuration. See Figure 1.1 and Figure for
(Local Control	front and rear panel diagrams.
Mode)	Table 3.1 Shipped Configuration (Local Control Mode)
	Local Control Configuration	Additional References

Use the front panel controls to adjust the output voltage and current limit settings. (Note: Use the LOCAL button only when you have a digital programming interface installed.)

See Section 3 for front panel operation. See Section 4 for remote analog programming procedure(s).

The supply's sense point is at the rear panel	See “Local and Remote Sensing” on
J10 sense connector terminals.	page 53 for how to change from local to
	remote sensing.
The OVP set point is adjusted at the front	See “Using Over Voltage Protection
panel to approximately 110% of rated output	(OVP)” on page 61 for the adjustment
voltage.	procedure.
The over temperature shutdown function	See “Over Temperature Protection
automatically resets when activated as	(OTP)” on page 70 for more
determined by the position of rear panel	information about switch SW1-8
switch SW1-8. A latch off setting is also	settings.
available.

Release 2.1

59

Image 61

Contents XFR 2800 Watt Series Programmable DC Power Supply Page XFR 2800 Watt Series What does this warranty cover and how long does it last? How do you get service?What will Xantrex do? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyPower Supply Safety Main Sections Who Should Use This ManualManual Revisions About This Manual Power Supply Safety MarkingsContents Calibration Section Local Operation RemoteList of Figures List of Figures List of Tables List of Tables Description Features and OptionsModel Voltage Range Current Range Features and Specifications Front Panel Controls Power Supply Front PanelRear Panel Connectors and Switch Power Supply Rear Panel Shows the functions assigned to each SW1 switch HIGH=OFF HIGH=ON Switch Function Open ClosedProgramming and Monitoring J2 Connector Vrmt Connector Reference Name FunctionMaking J2 Connections WiringSpecifications Models 300 12-220 20-130 33-85 40-70 Features and Specifications Models 60-46 100-28 150-18 300-9 600-4 Features and Specifications Input Conditions Additional SpecificationsRemote Programming Monitoring Additional FeaturesEnvironmental Specifications Output Connector Mechanical SpecificationsDimensional Drawings Introduction Basic Setup ProcedureStep # Description Action Reference Initial Inspection Periodic Cleaning Inspection, Cleaning, and PackagingReturning Power Supplies to the Manufacturer Shipping or Storage Carton Label Packaging for Shipping or StorageRack Mounting Location, Mounting, and VentilationAC Input Connector Voltage Selection AC Input PowerAC Input AC Voltage Range FrequencyWire Size Ratings Cable Outside Diameter AC Input Wire ConnectionAC Input Cover and Strain Relief Power-on Check Voltage Mode Operation CheckFunctional Tests Equipment RequiredCurrent Mode Operation Check Front Panel Function Checks Wire Size Maximum Current a Load WiringLoad Connection Making Load Connections Maximum Load Wire Length for 1 V Line DropOutput Strain Relief and Cover Typical Load Connection Hardware To 600 V Models Output Voltage ConnectorSingle Load with Local Sensing Default Multiple Loads with Local Sensing 10Multiple Loads with Remote Sensing Local and Remote Sensing Sense WiringTerminal Name Function 11J10 Sense ConnectorUsing Remote Sensing 12 shows a sample setup for using remote sensing Operating Modes Automatic Crossover Standard OperationStandard Operation Local OperationShipped ConfigurationMode Setting Output Voltage Current Limit OVP Using Over Voltage Protection OVPResetting the OVP Circuit Controlling Shutdown Function via Connector Using the Shutdown FunctionLED Configuring Multiple Supplies for Series Operation Using Multiple SuppliesParallel ConfiguringSupplies for Parallel Operation of Multiple Supplies Supplies for Split Supply OperationSplit Supply Operation of Multiple Supplies Positive-negative SupplyLocal Operation Switch SW1-8 OTP Shutdown Selection Description Over Temperature Protection OTPEmergency Shutdown User DiagnosticsUnusual or Erratic Operation Abbreviated References Used in TableSymptom Check Further Checks and Corrections Remote Operation Options Remote Analog Programming ProcedureRemote Operation Control Programming ScalesRemote Operation Power Supply Settings for Different Programming Sources Connecting Programming Sources to J2 Connector Remote Monitoring of Output Voltage and Current Service Calibration SetupPrecautions EnvironmentAccessing Calibration Potentiometers Programming and Monitoring Calibration Locations Voltage Programming Circuit Calibration Calibrating for Programming AccuracyCurrent Limit Programming Circuit Calibration Output Voltage Monitor Circuit Calibration Calibrating for Readback AccuracyOutput Current Monitor Circuit Calibration Calibration Page Xantrex Technology Inc