Xantrex Technology XFR 2800 manual Additional Features, Remote Programming Monitoring

Page 33

Features and Specifications

Specifications

Additional

Features

Switching Frequency	nominal 31 kHz (62 kHz output ripple).

Output Hold-up Time	Greater than 10 ms with interruption of AC line,
	for nominal AC input and full load.

Maximum Voltage Differential from	±600 Vdc
either output to safety ground

Insulation Resistance	Input to chassis: >30 MΩ, with 500 Vdc;
	Output to chassis: >20 MΩ, with 1000 Vdc.

Isolation Voltage	Input to output: 1350 Vac

Remote

Programming

and

Monitoring

Remote Start/Stop and Interlock	2.5-15 V signal or TTL-compatible input,
	selectable logic. TTL input impedance: 2 k (in
	series with one diode drop).

Remote Analog Programming (Full	Voltage and current programming inputs
Scale Input)	(source must be isolated): 0-5 k, 0-10 k
	resistances; 0-5 V, 0-10 V (default) voltage
	sources. Input impedance (V and I):
	approximately 100 k.

Remote Monitoring	Output voltage and current: 0-5 V, 0-10 V
	(default);
	Output impedance (V and I): approximately
	221 Ω.
	Output short circuit current: approximately
	50 mA.

Remote Programming and	1% zero to full scale output for the default
Monitoring Accuracy	range.

Maximum Remote Sense Line Drop	5 V/line (Line drop is subtracted from total voltage
Compensation	available at supply output.)

Optional Isolated Program and	0-5 V (ISOL interface); input impedance: 200 k;
Readback (V&I)	output impedance: 221 Ω.

Optional Digital Control	RS-232, GPIB interfaces

Release 2.1

31

Image 33

Contents XFR 2800 Watt Series Programmable DC Power Supply Page XFR 2800 Watt Series What does this warranty cover and how long does it last? How do you get service?What will Xantrex do? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyPower Supply Safety Who Should Use This Manual Main SectionsManual Revisions About This Manual Power Supply Safety MarkingsContents Calibration Section Local Operation RemoteList of Figures List of Figures List of Tables List of Tables Features and Options DescriptionModel Voltage Range Current Range Features and Specifications Front Panel Controls Power Supply Front PanelRear Panel Connectors and Switch Power Supply Rear Panel Shows the functions assigned to each SW1 switch HIGH=OFF HIGH=ON Switch Function Open ClosedProgramming and Monitoring J2 Connector Vrmt Connector Reference Name FunctionMaking J2 Connections WiringSpecifications Models 300 12-220 20-130 33-85 40-70 Features and Specifications Models 60-46 100-28 150-18 300-9 600-4 Features and Specifications Input Conditions Additional SpecificationsRemote Programming Monitoring Additional FeaturesEnvironmental Specifications Output Connector Mechanical SpecificationsDimensional Drawings Basic Setup Procedure IntroductionStep # Description Action Reference Initial Inspection Periodic Cleaning Inspection, Cleaning, and PackagingReturning Power Supplies to the Manufacturer Shipping or Storage Carton Label Packaging for Shipping or StorageRack Mounting Location, Mounting, and VentilationAC Input Connector Voltage Selection AC Input PowerAC Input AC Voltage Range FrequencyWire Size Ratings Cable Outside Diameter AC Input Wire ConnectionAC Input Cover and Strain Relief Power-on Check Voltage Mode Operation CheckFunctional Tests Equipment RequiredCurrent Mode Operation Check Front Panel Function Checks Load Wiring Wire Size Maximum Current aLoad Connection Making Load Connections Maximum Load Wire Length for 1 V Line DropOutput Strain Relief and Cover Typical Load Connection Hardware To 600 V Models Output Voltage ConnectorSingle Load with Local Sensing Default Multiple Loads with Local Sensing 10Multiple Loads with Remote Sensing Local and Remote Sensing Sense WiringTerminal Name Function 11J10 Sense ConnectorUsing Remote Sensing 12 shows a sample setup for using remote sensing Operating Modes Automatic Crossover Standard OperationStandard Operation Local OperationConfiguration ShippedMode Setting Output Voltage Current Limit OVP Using Over Voltage Protection OVPResetting the OVP Circuit Controlling Shutdown Function via Connector Using the Shutdown FunctionLED Configuring Multiple Supplies for Series Operation Using Multiple SuppliesConfiguring ParallelSupplies for Parallel Operation of Multiple Supplies Supplies for Split Supply OperationSplit Supply Operation of Multiple Supplies Positive-negative SupplyLocal Operation Switch SW1-8 OTP Shutdown Selection Description Over Temperature Protection OTPEmergency Shutdown User DiagnosticsUnusual or Erratic Operation Abbreviated References Used in TableSymptom Check Further Checks and Corrections Remote Operation Options Remote Analog Programming ProcedureRemote Operation Control Programming ScalesRemote Operation Power Supply Settings for Different Programming Sources Connecting Programming Sources to J2 Connector Remote Monitoring of Output Voltage and Current Service Calibration SetupPrecautions EnvironmentAccessing Calibration Potentiometers Programming and Monitoring Calibration Locations Voltage Programming Circuit Calibration Calibrating for Programming AccuracyCurrent Limit Programming Circuit Calibration Output Voltage Monitor Circuit Calibration Calibrating for Readback AccuracyOutput Current Monitor Circuit Calibration Calibration Page Xantrex Technology Inc