Xantrex Technology XFR 2800 User Diagnostics, Emergency Shutdown, Unusual or Erratic Operation

Page 73

Local Operation

User Diagnostics

User Diagnostics

Emergency Shutdown

If your power supply is not performing as described in this operating manual, run through the procedures and checks in this section before calling your service technician. These procedures are confined to operator-level functions only and do not require cover-off servicing.

In an emergency, carry out both of these steps:

1.Shut the power supply OFF immediately.

2.Disconnect the power supply from the load.

Unusual or Erratic Operation

Troubleshooting for Operators

If the power supply displays any unusual or erratic operation, follow these steps:

1.Shut the power supply OFF immediately.

2.Disconnect the power supply from the load.

3.Test the power supply with no load, running the tests in Functional Tests.

4.If the tests show that the power supply is functioning normally, check all load, programming, and monitoring connections and circuits.

5.Check the AC input for correct voltage and frequency.

If the problem is not solved after following this procedure, or if the unit fails to operate correctly upon retesting, call your service technician.

Turn to the next page for more information about troubleshooting for operators.

Use the checks in Table 3.4 to ensure that the power supply is configured and connected for normal operation.

Abbreviated References Used in Table

ACF

AC fail

OTP

over temperature protection

OVP

over voltage protection

REM

remote mode

S/D

shutdown

Release 2.1

71

Image 73
Contents XFR 2800 Watt Series Programmable DC Power Supply Page XFR 2800 Watt Series What does this warranty cover and how long does it last? How do you get service?What will Xantrex do? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyPower Supply Safety Main Sections Who Should Use This ManualManual Revisions About This Manual Power Supply Safety MarkingsContents Calibration Section Local Operation RemoteList of Figures List of Figures List of Tables List of Tables Description Features and OptionsModel Voltage Range Current Range Features and Specifications Front Panel Controls Power Supply Front PanelRear Panel Connectors and Switch Power Supply Rear Panel Shows the functions assigned to each SW1 switch HIGH=OFF HIGH=ON Switch Function Open ClosedProgramming and Monitoring J2 Connector Vrmt Connector Reference Name FunctionMaking J2 Connections WiringSpecifications Models 300 12-220 20-130 33-85 40-70 Features and Specifications Models 60-46 100-28 150-18 300-9 600-4 Features and Specifications Input Conditions Additional SpecificationsRemote Programming Monitoring Additional FeaturesEnvironmental Specifications Output Connector Mechanical SpecificationsDimensional Drawings Introduction Basic Setup ProcedureStep # Description Action Reference Initial Inspection Periodic Cleaning Inspection, Cleaning, and PackagingReturning Power Supplies to the Manufacturer Shipping or Storage Carton Label Packaging for Shipping or StorageRack Mounting Location, Mounting, and VentilationAC Input Connector Voltage Selection AC Input PowerAC Input AC Voltage Range FrequencyWire Size Ratings Cable Outside Diameter AC Input Wire ConnectionAC Input Cover and Strain Relief Power-on Check Voltage Mode Operation CheckFunctional Tests Equipment RequiredCurrent Mode Operation Check Front Panel Function Checks Wire Size Maximum Current a Load WiringLoad Connection Making Load Connections Maximum Load Wire Length for 1 V Line DropOutput Strain Relief and Cover Typical Load Connection Hardware To 600 V Models Output Voltage ConnectorSingle Load with Local Sensing Default Multiple Loads with Local Sensing 10Multiple Loads with Remote Sensing Local and Remote Sensing Sense WiringTerminal Name Function 11J10 Sense ConnectorUsing Remote Sensing 12 shows a sample setup for using remote sensing Operating Modes Automatic Crossover Standard OperationStandard Operation Local OperationShipped ConfigurationMode Setting Output Voltage Current Limit OVP Using Over Voltage Protection OVPResetting the OVP Circuit Controlling Shutdown Function via Connector Using the Shutdown FunctionLED Configuring Multiple Supplies for Series Operation Using Multiple SuppliesParallel ConfiguringSupplies for Parallel Operation of Multiple Supplies Supplies for Split Supply OperationSplit Supply Operation of Multiple Supplies Positive-negative SupplyLocal Operation Switch SW1-8 OTP Shutdown Selection Description Over Temperature Protection OTPEmergency Shutdown User DiagnosticsUnusual or Erratic Operation Abbreviated References Used in TableSymptom Check Further Checks and Corrections Remote Operation Options Remote Analog Programming ProcedureRemote Operation Control Programming ScalesRemote Operation Power Supply Settings for Different Programming Sources Connecting Programming Sources to J2 Connector Remote Monitoring of Output Voltage and Current Service Calibration SetupPrecautions EnvironmentAccessing Calibration Potentiometers Programming and Monitoring Calibration Locations Voltage Programming Circuit Calibration Calibrating for Programming AccuracyCurrent Limit Programming Circuit Calibration Output Voltage Monitor Circuit Calibration Calibrating for Readback AccuracyOutput Current Monitor Circuit Calibration Calibration Page Xantrex Technology Inc