Fujitsu PRN608-S user manual D1,d2,..,dX

Page 33

PRN608-S

PAPER OFFSET (default 2mm) This value is the length between Black Mark and start of printing. Value must be between 2 mm. and Page length – 2mm. BLACKMARK LENGTH (default 15mm). This is the length of the Black Marks.

The board can be set to transmit a ’B’ whenever the paper is not detected at paper detect. This is typical when the sensor encounters a Black Mark.

The following commands is used for enabling Black

Mark

Default:

PAGELENGHT=150mm

PAPEROFFSET=2mm

BLACKMARK=120 (120/8=15mm)

ESC+205+1+98+n

n:Bit 0: if set the board will transmit ’B’ every time paper is not detected at the paper detector.

Bit 1: if set the Black Mark function is enable. Default n = 0.

3.8.43Graphic data – non compressed

[Name]

Graphic data – non-compressed

[Format]

ASCII

US

d1,d2,..,dX

 

Hex

1F

d1,d2,..,dX

 

Decimal

31

d1,d2,..,dX

[Range]

n: [0;255]

 

 

 

X=54 for FTP628MCLxxx, X=72 for FTP638MCLxxx,

[Description]

When the printer controller receives this command the

Xgraphic bytes (d1-dX) will be printed in one dot line. The MSB in d1 is the left most dot and the LSB in dX is the right most dot.

3.8.44Graphic data – compressed

[Name]

Graphic data – compressed

[Format]

ASCII

Y

d1,d2,..,d(-Y)

 

Hex

Y

d1,d2,..,d(-Y)

 

Decimal

Y

d1,d2,..,d(-Y)

[Range]

Y: [-X;-2]

 

 

 

n: [0;255]

 

 

X=54 for FTP628MCLxxx, X=72 for FTP638MCLxxx,

28-03-2003 Page 3-33 of 53

Image 33
Contents For Fujitsu Thermal Printers FTP608 Series Copyright 1999-2003 by I/F-COM A/S All rights reserved Safety Precautions1-3 System Description Installation Maintenance APS Compatible Command SET Optional FTP-628MCLxxx FTP-638MCLxxx InstallationUnpacking LabelsSettings Power supply2-9 2-10 Serial Input/Output 2-12 Thermal Head Control 2-14 2-15 Specifications General Serial communication USB communicationIrda communication Auto form feed Firmware upgradeCharacter design 3-20 I/F-COM simple command set Ascii ACK Ascii ENQAscii BEL AsciiAscii DC1 Ascii DLEAscii DC3 Ascii DC2Ascii DC4 Ascii NAKAscii ETB Ascii CanAscii SUB Ascii ESC Z PRN608-S Stop sending automatic status Name Format Change dot size Name Format PRN608-S Feed Paper Name Format Upca EAN13EAN8 ‘d’ Space Black Mark Name Set black mark parameters Format D1,d2,..,dX Escape Sequences Ascii Function Request analogue voltage Store/Transport Daily useMechanical Data Electrical DataEnvironmental Data EMC & ESCTemperature Test Pin Function Pin CUT GNDLED1+ LED2+ INPUT1 INPUT2 GND LED USB USB+ GND CTS DSRRTS DTR GNDOFF Seiko compatible command set optionalESC RS Fujitsu compatible command set optionalESC US ESC7-46 7-47 APS compatible command set optional ESC SGS E BIT Function BIT = 0 BIT = ESC/POS compatible command set optional ESC FFESC L 7-51 Bottom view Optional sensor description Top viewRED White Black