IBM C4C 4.51 3.5-inch Small FF 38-pin Unitized, SSA manual Vibration and Shock

Page 79

U S E R RESPONSIBLE F O R V E R I F Y I N G VERSION A N D COMPLETENESS

O E M F U N C T I O N A L S P E C I F I C A T I O N U L T R A S T A R X P ( D F H C ) SSA M O D E L S 1.12/2.25 G B - 1.0" H I G H

Notes: 1) Center thermocouple on the top surface of the module.

2)If copper tape is used to attach temperature sensors, it should be no larger than 6 m m square.

3)Dimensions are in millimeters.

4)The connector (on the left edge) does not represent SSA connector.

Figure 23. Temperature Measurement Points for all Models (bottom view)

7.2 Vibration and Shock

The operating vibration and shock limits in this specification are verified in two mount configurations for CxC models:

1.By mounting with the 6-32 bottom holes with the drive on 2 m m clearance as required by 4.1.2, “Clearances” on page 51

2.By mounting on any two opposing pairs of the 6-32 side mount holes.

CxB models are mounted rigidly to the test fixture using the carrier guides, connector, and latch mechanism. The test fixture is then mounted to the vibration table (the test fixture must not have any resonance within the frequencies tested).

Other mount configurations may result in different operating vibration and shock performance.

Source filename=OPLIMITS

I B M Corporation

Page 79 of 87

Page 78 Page 80
Image 79
Page 78 Page 80
Contents Form Factor Disk Drive Version BM Corporation Preface Source filename=STSSHEXT When Operating Limits ReliabilityContaminants Acoustic Levels Source filename=STSSHEXT Description FeaturesGeneral Features Interface Controller FeaturesModels Reliability FeaturesGeneral SpecificationsSectors/track sct/trk User bytes/sector ub/sctSectors/logical block sct/lba User bytes/logical block ub/lbaFor Each Notch Capacity EquationsFor Entire Drive + 1 2 Volts Supply Power Requirements by Model1 C1x Models Input Voltage + 5 Volts SupplyExample 3. Power Calculation Power Calculation ExamplesExample 1. Calculate the mean 12 volt average current Example 4. Calculate the 12 volt peak current Things to check when measuring 12 V supply currentVolt current during read/write operations C1x Models Typical 12 volt current C1x Models Typical 12 volt spin-up current C1x Models 2 C2x Models Power Calculation Examples Example 4. Calculate the 12 volt peak current Volt current during read/write operations C2x Models Typical 12 volt current C2x Models Typical 12 volt spin-up current C2x Models 3 C4x Models Power Calculation Examples Example 4. Calculate the 12 volt peak current Volt current during read/write operations C4x Models Typical 12 volt current C4x Models Typical 12 volt spin-up current C4x Models CxB Models Power supply methods4.2 DC/DC Converter Hot plug/unplug support Grounding Requirements of the Disk EnclosureM Corporation Event Nominal Maximum Bring-up Sequence and Stop TimesBring-up Sequence Times and Stop Time for C2x Models Source filename=PERFORM # of segments Ub/lba + PerformanceEnvironment Definition Workload DefinitionBasic Component Descriptions Command Execution TimeSequential RandomData Transfer to/from Disk Data Transfer to/from SSA Link CommentsTheoretical Data Sector Transfer Rate Approximating Performance for Different EnvironmentsWhen Read-ahead is Enabled When Read Caching is EnabledWhen Write Caching is Enabled When Adaptive Caching is EnabledBack-To-Back Commands When No Seek is RequiredFor Queued Commands Reordered CommandsCylinder to Cylinder Skew SkewTrack to Track Skew Idle Time Functions Channel Calibration Servo Run Out MeasurementsServo Bias Measurements Predictive Failure AnalysisSave Logs and Pointers Command Timeout LimitsDisk Sweep M Corporation Clearances Weight and DimensionsMechanical Small Form Factor Models CxCDimensions are in millimeters Location of Side Mounting Holes of C4C Models Source filename=MECHANIC Unitized Connector Locations Source filename=MECHANIC Carrier Models CxB Dimensions CxB Models M Corporation Handle Docking and Ejection System Auto-docking Assembly Side Rails Side Rail Positioning E D Locations front view CxB Models M Corporation Electrical Connector and Indicator LocationsElectrical Interface SSA Unitized ConnectorPin Carrier ConnectorRow Option Pins and Indicators SSA Link Electrical CharacteristicsSSA Link Cable Ground long Option Port Pin Device Activity Pin/Indicator Option Port PinDevice Fault Pin/Indicator Option Port Pin Write Protect Option Port PinProgrammable pin 1 Option Port Pin Front Jumper ConnectorEarly Power Off Warning or Power Fail Power Port Pin 12 12V Charge and 5V Charge Power Port pin 1Spindle Synchronization Over Sync Hard-wire M Corporation Source filename=RELIABLE Reliability Error DetectionSeek Error Rate Power On Hours ExamplesProduct Life Power on/off cyclesUseful Life Maximum on/off cyclesSample Failure Rate Projections Install Defect FreeMean Time Between Failure *MTBF Spql Shipped product quality levelESD Protection Periodic MaintenanceConnector Insertion Cycles Install Defect Free percentage PercentOperating Limits Temperature Measurement PointsP F E T Maximum ReliabilityVibration and Shock Temperature Measurement Points for all Models bottom viewOutput Vibration Limits Drive Mounting GuidelinesOperating Vibration V4S Nonoperating VibrationOperating Shock ContaminantsNonoperating Shock Acoustic Levels Upper Limit Sound Power Requirements Bels for C4x ModelsSource filename=STANDARD Standards SafetyElectromagnetic Compatibility EMC M Corporation Serial Storage Architecture S S a P H Transport Bibliography
Top Page Image Contents