Cisco Systems (VIP6-80) manual Introduction, Contents

Page 1

Versatile Interface Processor (VIP6-80)

Installation and Configuration Guide

Product Numbers: VIP6-80(=), MEM-VIP6-64M-SD(=), MEM-VIP6-128M-SD(=), MEM-VIP6-256M-SD(=)

Customer Order Number DOC-7814372=

Introduction

This document describes the Versatile Interface Processor (VIP6-80), an option available for use with the Cisco 7500 series and the Cisco 7000 series routers using the 7000 Series Route Switch Processor (RSP7000) and 7000 Series Chassis Interface (RSP7000CI). The VIP6-80 improves high-performance switching over previous generation VIPs.

The VIP6-80 supports online insertion and removal (OIR), a feature that allows you to remove and replace a VIP6-80 without first shutting down the system. However, the VIP6-80 does not support OIR of port adapters (PAs). The VIP6-80 must be removed before removing or installing the port adapter.

The VIP6-80 also supports Single Line Card Reload, a feature that reloads a failed line card on the network backplane without reloading other line cards. Refer to the “Single Line Card Reload” section on page 32 for more information.

The VIP6-80 supports any combination of LAN and WAN PAs, including Fast Ethernet, T1/E1, High-Speed Serial Interface (HSSI), T3/E3, T3/E3 ATM, multichannel T1/E1, multichannel T3/E3, OC-3 ATM, Packet over SONET (POS), and OC-12 ATM. For a list of supported port adapters, refer to the “Port Adapter Slots” section on page 7.

Contents

This guide includes the following sections:

•Related Documentation, page 2

•Product Description, page 3

•Installation Prerequisites, page 10

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 2003 Cisco Systems, Inc. All rights reserved.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Introduction ContentsRelated Documentation Product Description VIP6-80 Features Memory Components CPUJumpers LEDsMicrocode ROM MonitorPA-2FE-TX Port Adapter SlotsPA-2FE-FX System Software SpecificationsTraffic Management Installation PrerequisitesSoftware Requirements Hardware RequirementsMicrocode Requirements Agency Approvals Safety GuidelinesTools and Parts Required Safety Warnings Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation Handling Interface Processors-Vertical Orientation Shown Bottom ejector lever Processor module slot Module Removing a VIP6-80 Removing and Installing Port Adapters Handling a Port Adapter Single-Width Port AdapterRemoving and Installing a Single-Width Port Adapter Location of VIP6-80 Slot Divider and Screws Dual-Width Port AdapterRemoving and Installing a Dual-Width Port Adapter Connecting Cables to the Port Adapter Installing a VIP6-80Performing a Basic Configuration Verifying the Installation Checking the VIP6-80 InstallationRemoval InsertionPage Using show Commands to Verify the VIP6-80 Status Router# show controllers cbus Using show Commands to Display Interface InformationShow controllers command RMA Using the ping Command to Verify Network ConnectivitySingle Line Card Reload Maintenance ProceduresUpgrading VIP6-80 Memory Product Description Opening the Dimm Socket Tabs Removing Sdram DIMMsInserting the Dimm Installing Sdram DIMMsChecking the VIP6-80 Memory Upgrade TroubleshootingCisco.com Obtaining DocumentationDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and InformationOL-5078-01
Top Page Image Contents