Cisco Systems (VIP6-80) manual Troubleshooting, Checking the VIP6-80 Memory Upgrade

Page 36

Checking the VIP6-80 Memory Upgrade

This section describes how you would verify the memory upgrade.

•Observe the LED states and the console display. As the system reinitializes the interfaces, the enabled LEDs on the VIP6-80 PAs should go on. (Port adapter status LEDs might be on, depending on your connections.) The console screen also displays a message as the system discovers each interface during its reinitialization.

•Use the show diag command to verify that the system recognizes the new memory; check the line of the show diag command output (see page 30) that begins with Controller Memory Size.

•If the system fails to boot properly, if the console terminal displays a checksum or memory error, or if the show diag command output indicates an incorrect amount of memory (or no memory), check the following:

–Ensure that all memory devices are installed correctly. If necessary, shut down the system and remove the VIP6-80. Check the memory devices by looking straight down on them and then at eye level. The devices should be aligned at the same angle and the same height when properly installed. If a memory device appears to stick out or rest in the socket at a different angle from the others, remove the device and reinsert it; then replace the VIP6-80 and reboot the system for another installation check.

–Each DIMM socket must contain a DIMM of the correct size and speed or the system cannot operate. To ensure this, use only memory devices that are included with Cisco Systems memory kits.

–See the “Checking the VIP6-80 Installation” section on page 26.

•If after several attempts the system fails to restart properly, contact TAC (see the “Obtaining Technical Assistance” section on page 38), or a service representative for assistance. Before you call, make note of any error messages, unusual LED states, or any other indications that might help solve the problem.

This completes the VIP6-80 memory upgrade verification.

Troubleshooting

This section includes information on VIP6-80 troubleshooting.

To troubleshoot the VIP6-80, refer to Troubleshooting VIP Crashes online at http://www.cisco.com/warp/customer/63/vip_crash.html (which requires user registration to access). To become a registered user, refer to http://www.cisco.com/register/.

Listed below are commonsense guidelines to troubleshoot the router, the VIP6-80 and its memory components, and the port adapter installation:

•Verify that the router is plugged in.

•Visually inspect the routers, the port adapters, and the VIP6-80 and its components to confirm that they appear to be in working order. Check to see that the LEDs are lighting up.

•Remove and reinstall the VIP6-80 to reseat it. Proceed to either the “Removing a VIP6-80” section on page 18 to replace a VIP6-80 or to the “Installing a VIP6-80” section on page 24 to install a new VIP6-80.

•If you replaced the SDRAM DIMMs, remove and reinstall them to reseat them. See the “Upgrading VIP6-80 Memory” section on page 32.

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

36

OL-5078-01

 

 

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Contents IntroductionRelated Documentation Product Description VIP6-80 Features CPU Memory ComponentsLEDs JumpersMicrocode ROM MonitorPort Adapter Slots PA-2FE-TXPA-2FE-FX Specifications System SoftwareInstallation Prerequisites Traffic ManagementSoftware Requirements Hardware RequirementsAgency Approvals Safety Guidelines Microcode RequirementsTools and Parts Required Safety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation Handling Interface Processors-Vertical Orientation Shown Bottom ejector lever Processor module slot Module Removing a VIP6-80 Removing and Installing Port Adapters Single-Width Port Adapter Handling a Port AdapterRemoving and Installing a Single-Width Port Adapter Dual-Width Port Adapter Location of VIP6-80 Slot Divider and ScrewsRemoving and Installing a Dual-Width Port Adapter Installing a VIP6-80 Connecting Cables to the Port AdapterPerforming a Basic Configuration Checking the VIP6-80 Installation Verifying the InstallationRemoval InsertionPage Using show Commands to Verify the VIP6-80 Status Using show Commands to Display Interface Information Router# show controllers cbusShow controllers command Using the ping Command to Verify Network Connectivity RMAMaintenance Procedures Single Line Card ReloadUpgrading VIP6-80 Memory Product Description Removing Sdram DIMMs Opening the Dimm Socket TabsInstalling Sdram DIMMs Inserting the DimmTroubleshooting Checking the VIP6-80 Memory UpgradeObtaining Documentation Cisco.comDocumentation CD-ROM Ordering DocumentationObtaining Technical Assistance Documentation FeedbackCisco TAC Website Opening a TAC Case Obtaining Additional Publications and Information TAC Case Priority DefinitionsOL-5078-01
Top Page Image Contents