Cisco Systems (VIP6-80) Installation Prerequisites, Traffic Management, Software Requirements

Page 10

Traffic Management

The VIP6-80 supports the following:

Simple Network Management Protocol (SNMP) agent V1 (RFCs 1155–1157)

Management Information Base (MIB) II (RFC 1213)

Installation Prerequisites

This section provides installation prerequisites to ensure a successful VIP6-80 installation, and includes the following sections:

Software Requirements, page 10

Hardware Requirements, page 10

Microcode Requirements, page 11

Tools and Parts Required, page 11

Agency Approvals, page 11

Safety Guidelines, page 11

Software Requirements

The minimum Cisco IOS Release requirements for VIP6-80 are listed in Table 6. For configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware.

 

Note

You can access Cisco IOS software configuration and hardware installation and maintenance

 

 

documentation on the World Wide Web at http://www.cisco.com. Translated documentation is available

 

 

at the following URL: http://www.cisco.com/public/countries_languages.shtml.

 

 

 

 

Table 6

VIP6-80 Minimum Software Release Requirements

 

 

 

VIP Release

 

Minimum Cisco IOS Supported Releases

 

 

 

 

VIP6-80

 

 

Cisco IOS Release 12.0(22)S or later release of Cisco IOS Release 12.0 S

 

 

 

Cisco IOS Release 12.1(12)E or later release of Cisco IOS Release 12.1 E

 

 

 

Cisco IOS Release 12.2(12)T or later release of Cisco IOS Release 12.2 T

 

 

 

 

Hardware Requirements

The VIP6-80 is a single motherboard. It operates with the following:

Cisco 7505, Cisco 7507, Cisco 7507-MX, Cisco 7513, Cisco 7513-MX, and the Cisco 7576 routers with the Route Switch Processor (RSP1, RSP2, RSP4, RSP4+, RSP8, or RSP16); the RSP should have at least 64 MB of DRAM

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

10

OL-5078-01

 

 

Image 10
Contents Contents IntroductionRelated Documentation Product Description VIP6-80 Features CPU Memory ComponentsMicrocode LEDsJumpers ROM MonitorPort Adapter Slots PA-2FE-TXPA-2FE-FX Specifications System SoftwareSoftware Requirements Installation PrerequisitesTraffic Management Hardware RequirementsMicrocode Requirements Agency Approvals Safety GuidelinesTools and Parts Required Safety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation Handling Interface Processors-Vertical Orientation Shown Bottom ejector lever Processor module slot Module Removing a VIP6-80 Removing and Installing Port Adapters Single-Width Port Adapter Handling a Port AdapterRemoving and Installing a Single-Width Port Adapter Dual-Width Port Adapter Location of VIP6-80 Slot Divider and ScrewsRemoving and Installing a Dual-Width Port Adapter Installing a VIP6-80 Connecting Cables to the Port AdapterPerforming a Basic Configuration Removal Checking the VIP6-80 InstallationVerifying the Installation InsertionPage Using show Commands to Verify the VIP6-80 Status Using show Commands to Display Interface Information Router# show controllers cbusShow controllers command Using the ping Command to Verify Network Connectivity RMASingle Line Card Reload Maintenance ProceduresUpgrading VIP6-80 Memory Product Description Removing Sdram DIMMs Opening the Dimm Socket TabsInstalling Sdram DIMMs Inserting the DimmTroubleshooting Checking the VIP6-80 Memory UpgradeDocumentation CD-ROM Obtaining DocumentationCisco.com Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case Obtaining Additional Publications and Information TAC Case Priority DefinitionsOL-5078-01