Cisco Systems (VIP6-80) manual Using show Commands to Verify the VIP6-80 Status

Page 28

Step 9 Repeat Step 1 through Step 8 to verify that any additional VIP6-80s are properly installed.

This completes the VIP6-80 installation.

If you experience other problems that you are unable to solve, contact TAC (see the “Obtaining Technical Assistance” section on page 38), or a service representative for assistance.

To configure the new interface, use the configuration section of the specific port adapter installation and configuration guide, or the Cisco IOS software configuration documentation listed in the “Related Documentation” section on page 2. The documentation is available online on Cisco.com, and on the Documentation CD-ROM.

Using show Commands to Verify the VIP6-80 Status

The following steps use show commands to verify that the new interfaces are configured and operating correctly.

Step 1 Use the show version command to display the system hardware configuration. Ensure that the list includes the new interfaces.

Step 2 Display all the current interface processors and their interfaces with the show controllers command. Verify that the new VIP6-80 appears in the correct interface processor slot.

Step 3 Specify one of the new interfaces with the show interfaces type interface-processor-slot-number/port-adapter-slot-number/interface-port-numbercommand and verify that the first line of the display specifies the interface with the correct slot number. Also verify that the interface and line protocol are in the correct state: up or down.

Step 4 Display the protocols configured for the entire system and specific interfaces with the show protocols command. If necessary, return to configuration mode to add or remove protocol routing on the system or specific interfaces.

Step 5 Display the running configuration file with the show running-configcommand. Display the configuration stored in the RSP NVRAM using the show startup-configcommand. Verify that the configuration is accurate for the system and each interface.

If the interface is down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the network interface is properly connected and terminated. If you still have problems bringing the interface up, contact a service representative for assistance.

This completes the procedure to verify that the new interfaces are properly configured, using the show commands.

Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

28

OL-5078-01

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Contents IntroductionRelated Documentation Product Description VIP6-80 Features CPU Memory ComponentsLEDs JumpersMicrocode ROM MonitorPort Adapter Slots PA-2FE-TXPA-2FE-FX Specifications System SoftwareInstallation Prerequisites Traffic ManagementSoftware Requirements Hardware RequirementsMicrocode Requirements Agency Approvals Safety GuidelinesTools and Parts Required Safety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation Handling Interface Processors-Vertical Orientation Shown Bottom ejector lever Processor module slot Module Removing a VIP6-80 Removing and Installing Port Adapters Single-Width Port Adapter Handling a Port AdapterRemoving and Installing a Single-Width Port Adapter Dual-Width Port Adapter Location of VIP6-80 Slot Divider and ScrewsRemoving and Installing a Dual-Width Port Adapter Installing a VIP6-80 Connecting Cables to the Port AdapterPerforming a Basic Configuration Checking the VIP6-80 Installation Verifying the InstallationRemoval InsertionPage Using show Commands to Verify the VIP6-80 Status Using show Commands to Display Interface Information Router# show controllers cbusShow controllers command Using the ping Command to Verify Network Connectivity RMASingle Line Card Reload Maintenance ProceduresUpgrading VIP6-80 Memory Product Description Removing Sdram DIMMs Opening the Dimm Socket TabsInstalling Sdram DIMMs Inserting the DimmTroubleshooting Checking the VIP6-80 Memory UpgradeObtaining Documentation Cisco.comDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case Obtaining Additional Publications and Information TAC Case Priority DefinitionsOL-5078-01
Top Page Image Contents