Cisco Systems IGX 8400 Series manual Pass-Through and Standard External UVM E1 Cabling

Page 21

Installing Voice Cards

Figure 3-9 Pass-Through and Standard (External) UVM E1 Cabling

Pass-throughPassed-

through

Passing (transparent)

A. One pass-through line

UVM 1

UVM 2

External

B. External line	UVM	H9888

The back slot line numbers correspond to the slot number in which the BC-UVI-2E1EC card resides. Record the back slot number and port number of each line. These numbers are necessary for conﬁguring the system after you complete hardware installation.

Card Installation and Node Startup 3-21

Image 21

Contents Preparing the Cards Card Installation and Node StartupPreparing the Cards IGX 8410 Cards, Front View IGX 8410 Cards, Back View IGX 8420 Card Shelf, Front View IGX 8430 Back View Inserting Modules Inserting the CardsHssi Making Signal ConnectionsConnecting Trunks Setting Up a UXM-EBringing Up a UXM-E Trunk Cable Management Dspcds Inverse Multiplexing over ATM on TrunksAdding Links to an IMA Feeder Group Adding an IMA Feeder TrunkRemoving Links from an IMA Feeder Group UXM-E Inverse Multiplexing ATM IMA LinesConnecting an NTM E1 or Subrate Trunk Connecting an NTM T1 or Y1 TrunkBringing Up a UXM-E in UNI or NNI Port Mode Connecting a CVM to a T1 or J1 Line Installing Voice CardsTDM Transport on the CVM Connecting a CVM to an E1 Line or a Subrate TrunkConnecting a UVM to T1 Lines Pass-Through and Standard External UVM T1 Cabling Connecting a UVM to E1 Lines Pass-Through and Standard External UVM E1 Cabling Connecting a UVM to J1 Lines 10 Pass-Through and Standard External UVM J1 Cabling 11 SDI and LDI Faceplates Making Serial Data ConnectionsConﬁguring the Port Modes of the HDM Back Cards HDM and LDM Redundancy Conﬁguring the Mode of an LDI Port13 Connecting a DTE or DCE Adapter Cable to an LDI Setting Up Frame Relay on a UFM Maximum Connections Per Port with Signalling ProtocolsMaking Frame Relay Connections Cable Redundancy on the UFMs14 Y-Cable Redundancy with Single and Dual-Port Cabling Setting Up Frame Relay Ports and Connections UFM Connecting UFM CablingSetting Up Frame Relay on an FRM Commands for T1/E1 Frame RelayDeleting a Frame Relay Port Port Mode Selection for V.35 Frame Relay Card Redundancy 15 Setting the Port Mode DTE/DCE on an FRISetting Up Frame Relay Ports and Connections FRM Making Alarm Relay Output Connections 36Cisco IGX 8400 Series Installation and Configuration Connecting a Single Network Management Station Making External Clock ConnectionsAttaching Peripherals 16 Connecting the Control Terminal 17 LAN Connection to SCM LAN Connection for the Network Management StationConﬁguring the LAN Port D2.cb1 LAN superuser IGX 42Cisco IGX 8400 Series Installation and Configuration Connecting a Network Management Station to Multiple Networks 20 Connecting a Network Printer Connecting the Printer21 Connecting Modems to an IGX Node Connecting a ModemInitial Startup of the IGX Connecting the Power Supply MonitorFail screen looks like this NPM Startup Diagnostic TestInspecting Status Lights Card Self TestIGX Conﬁguration Summary Checking the Power Supplies AC Systems50Cisco IGX 8400 Series Installation and Configuration Interworking Connections in a Tiered Network Conﬁguring an IGX Switch to Be an Interface ShelfConverting a Routing Node to an Interface Shelf Adding Connections in a Tiered Network through the CLI