Cisco Systems IGX 8400 Series manual D2.cb1 LAN superuser IGX

Page 41

Attaching Peripherals

•GatewayIPAddr is the Internet gateway address. This is the gateway that trafﬁc is routed through if the IGX node and workstation are on different networks. If they are on the same network, the gateway is not used. The default “none” is displayed in this case. If a gateway IP is entered and later you want to remove it, enter 192.0.0.0 opposite the prompt and “none” will again be displayed.

A cnﬂan screen looks like this:

D2.cb1	LAN superuser IGX 8410	9.3 Feb. 27 2000 14:23 PST
Active IP Address:		192.187.207.21
IP Subnet Mask:		255.255.255.0
TCP Service Port:		5130
Default Gateway IP Address:		192.187.207.1
Maximum LAN Transmit Unit:		1500
Ethernet Address:		00.55.43.00.04.55
Control Socket - Ready
Base Socket Descriptor - 1
Socket Closed
Last Command: cnflan
Next Command:

The active IP address for the workstation has been entered as the IP address selected previously for the node, 192.187.207.21. The IP Subnet mask is entered as 255.255.255.0 for a Class C LAN network. The TCP service port is entered as 5120. Because the workstation and node are on different networks in this example, a gateway address of 192.187.207.1 has been entered. If the workstation and node are both on the same network, no gateway address is needed. The “Maximum LAN Transmit Unit” and “Ethernet Address” parameters are not conﬁgurable by the cnﬂan command. The “Ethernet Address” is a hardware address (“burned into the NPM card”) that is unique to each NPM card.

Step 4 Connect the Cisco WAN Manager workstation and the IGX node to a LAN network. Examples are shown in Figure 3-18and Figure 3-19.The LAN port on the IGX node provides a DB-15 connector that can be connected to a Y-cable which in turn is connected to an AUI as shown in Figure 3-19.

Step 5 To make sure a LAN connection on the IGX LAN port is good, an example hostname of “sanfran” entered in the conﬁg.sv ﬁle, enter the following at the Cisco WAN Manager workstation:

ping sanfran

Card Installation and Node Startup 3-41

Image 41

Contents Preparing the Cards Card Installation and Node StartupPreparing the Cards IGX 8410 Cards, Front View IGX 8410 Cards, Back View IGX 8420 Card Shelf, Front View IGX 8430 Back View Inserting Modules Inserting the CardsHssi Making Signal ConnectionsBringing Up a UXM-E Trunk Connecting TrunksSetting Up a UXM-E Cable Management Dspcds Inverse Multiplexing over ATM on TrunksAdding Links to an IMA Feeder Group Adding an IMA Feeder TrunkRemoving Links from an IMA Feeder Group UXM-E Inverse Multiplexing ATM IMA LinesConnecting an NTM E1 or Subrate Trunk Connecting an NTM T1 or Y1 TrunkBringing Up a UXM-E in UNI or NNI Port Mode Connecting a CVM to a T1 or J1 Line Installing Voice CardsTDM Transport on the CVM Connecting a CVM to an E1 Line or a Subrate TrunkConnecting a UVM to T1 Lines Pass-Through and Standard External UVM T1 Cabling Connecting a UVM to E1 Lines Pass-Through and Standard External UVM E1 Cabling Connecting a UVM to J1 Lines 10 Pass-Through and Standard External UVM J1 Cabling 11 SDI and LDI Faceplates Making Serial Data ConnectionsConﬁguring the Port Modes of the HDM Back Cards HDM and LDM Redundancy Conﬁguring the Mode of an LDI Port13 Connecting a DTE or DCE Adapter Cable to an LDI Setting Up Frame Relay on a UFM Maximum Connections Per Port with Signalling ProtocolsMaking Frame Relay Connections Cable Redundancy on the UFMs14 Y-Cable Redundancy with Single and Dual-Port Cabling Setting Up Frame Relay Ports and Connections UFM Connecting UFM CablingDeleting a Frame Relay Port Setting Up Frame Relay on an FRMCommands for T1/E1 Frame Relay Port Mode Selection for V.35 Frame Relay Card Redundancy 15 Setting the Port Mode DTE/DCE on an FRISetting Up Frame Relay Ports and Connections FRM Making Alarm Relay Output Connections 36Cisco IGX 8400 Series Installation and Configuration Attaching Peripherals Connecting a Single Network Management StationMaking External Clock Connections 16 Connecting the Control Terminal 17 LAN Connection to SCM LAN Connection for the Network Management StationConﬁguring the LAN Port D2.cb1 LAN superuser IGX 42Cisco IGX 8400 Series Installation and Configuration Connecting a Network Management Station to Multiple Networks 20 Connecting a Network Printer Connecting the Printer21 Connecting Modems to an IGX Node Connecting a ModemInitial Startup of the IGX Connecting the Power Supply MonitorFail screen looks like this NPM Startup Diagnostic TestInspecting Status Lights Card Self TestIGX Conﬁguration Summary Checking the Power Supplies AC Systems50Cisco IGX 8400 Series Installation and Configuration Interworking Connections in a Tiered Network Conﬁguring an IGX Switch to Be an Interface ShelfConverting a Routing Node to an Interface Shelf Adding Connections in a Tiered Network through the CLI