Cisco Systems IGX 8400 Series manual Making External Clock Connections, Attaching Peripherals

Page 37

Making External Clock Connections

Table 3-2shows the unassigned connector pins.

Table 3-2

Unassigned Connector Pins

 

 

 

Pin No.

Alarm Type

Alarm Description

 

 

 

7

Relay 2

common contact

 

 

 

8

Relay 2

normally closed contact

 

 

 

9

Relay 2

normally open contact

 

 

 

26

Relay 4

common contact

 

 

 

27

Relay 4

normally closed contact

 

 

 

28

Relay 4

normally open contact

 

 

 

Making External Clock Connections

The DB-15 connector labeled Ext Clocks on the faceplate of the SCM connects two external sources for a high-stability clock (primary and redundant). These inputs are 1.544 MHz or 2.048 MHz. In addition, one of the trunk or circuit line inputs can also serve as a source of timing for the node. If you do not select a clock source, the clock source is the internal IGX clock.

Two separate clock inputs exist. The primary clock source is A, and the secondary clock source is B. One or both of these can be either 1.544 Mbps or 2.048 Mbps. For a list of connector pin assignments, see Appendix C, “Cabling Summary.”

Attaching Peripherals

A network must have at least one control terminal (or a Cisco WAN Manager workstation if you wish to collect statistics) attached, along with a network printer for printing out the status of the system. The SCM has three ports for attaching peripherals to an IGX node. These ports are Control Terminal, LAN AUI, and AUX port.

For the Cisco TAC to perform remote troubleshooting, a modem must connect to the network. This is a requirement for all Cisco service plans. The following sections provide procedures for attaching peripherals to the IGX node. Be sure to read the manufacturers’ literature to ensure that the equipment is ready before attempting to connect it to the IGX node.

Connecting a Single Network Management Station

To use network management, at least one node in a Cisco WAN switching network running Release 7.2 or higher software must have a Cisco WAN Manager workstation connected. The workstation connects to the AUI Ethernet LAN port on the SCM.

The Cisco WAN Manager workstation can be used to configure and maintain all nodes in a network.

For instructions on using the Cisco WAN Manager workstation, see the

Cisco StrataView Plus Operations Guide.

If only a single NMS station is connected and the network is relatively small, you can use a serial

EIA/TIA232 port—the Control Terminal port.

The appendix titled “Peripherals Specifications” lists the control terminals supported by the IGX 8410 node and the configuration settings. Appendix C, “Cabling Summary” has the pin assignments for the IGX 8410 control terminal port.

Card Installation and Node Startup 3-37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Preparing the Cards Card Installation and Node StartupPreparing the Cards IGX 8410 Cards, Front View IGX 8410 Cards, Back View IGX 8420 Card Shelf, Front View IGX 8430 Back View Inserting Modules Inserting the CardsHssi Making Signal ConnectionsSetting Up a UXM-E Connecting TrunksBringing Up a UXM-E Trunk Cable Management Dspcds Inverse Multiplexing over ATM on TrunksAdding Links to an IMA Feeder Group Adding an IMA Feeder TrunkRemoving Links from an IMA Feeder Group UXM-E Inverse Multiplexing ATM IMA LinesConnecting an NTM E1 or Subrate Trunk Connecting an NTM T1 or Y1 TrunkBringing Up a UXM-E in UNI or NNI Port Mode Connecting a CVM to a T1 or J1 Line Installing Voice CardsTDM Transport on the CVM Connecting a CVM to an E1 Line or a Subrate TrunkConnecting a UVM to T1 Lines Pass-Through and Standard External UVM T1 Cabling Connecting a UVM to E1 Lines Pass-Through and Standard External UVM E1 Cabling Connecting a UVM to J1 Lines 10 Pass-Through and Standard External UVM J1 Cabling 11 SDI and LDI Faceplates Making Serial Data ConnectionsConfiguring the Port Modes of the HDM Back Cards HDM and LDM Redundancy Configuring the Mode of an LDI Port13 Connecting a DTE or DCE Adapter Cable to an LDI Setting Up Frame Relay on a UFM Maximum Connections Per Port with Signalling ProtocolsMaking Frame Relay Connections Cable Redundancy on the UFMs14 Y-Cable Redundancy with Single and Dual-Port Cabling Setting Up Frame Relay Ports and Connections UFM Connecting UFM CablingCommands for T1/E1 Frame Relay Setting Up Frame Relay on an FRMDeleting a Frame Relay Port Port Mode Selection for V.35 Frame Relay Card Redundancy 15 Setting the Port Mode DTE/DCE on an FRISetting Up Frame Relay Ports and Connections FRM Making Alarm Relay Output Connections 36Cisco IGX 8400 Series Installation and Configuration Making External Clock Connections Connecting a Single Network Management StationAttaching Peripherals 16 Connecting the Control Terminal 17 LAN Connection to SCM LAN Connection for the Network Management StationConfiguring the LAN Port D2.cb1 LAN superuser IGX 42Cisco IGX 8400 Series Installation and Configuration Connecting a Network Management Station to Multiple Networks 20 Connecting a Network Printer Connecting the Printer21 Connecting Modems to an IGX Node Connecting a ModemInitial Startup of the IGX Connecting the Power Supply MonitorFail screen looks like this NPM Startup Diagnostic TestInspecting Status Lights Card Self TestIGX Configuration Summary Checking the Power Supplies AC Systems50Cisco IGX 8400 Series Installation and Configuration Interworking Connections in a Tiered Network Configuring an IGX Switch to Be an Interface ShelfConverting a Routing Node to an Interface Shelf Adding Connections in a Tiered Network through the CLI
Top Page Image Contents